Hi, I'm Mark with Kimray. Today we're going to follow the pipes on an oil and

gas well site and then explain how each piece equipment operates.

This is a wellhead, this is where it all begins. The producer has drilled his well, in this

case, has had to set a rod pump in a pumping unit in order to get the liquid

to the surface. We'll follow the wellhead and go to the flow line to start the

separation process of oil water and gas, which could be very near the equipment

or in some cases over a mile in length before it gets to the equipment in order

to be processed. So the flow line coming from the wellhead comes up to this point.

All the oil all the fluid all the gas is coming through right through this line

to this two-phase vertical separator. Gas being lighter than liquid raises to the top

of the vessel. That's where the natural gas breaks out of the well stream, comes

down this pipe and into a Kimray back pressure valve. The back pressure valve

holds constant pressure on the vessels to allow it to move liquids to the next

destination. Any gas over the setpoint will be sold down this line over to the

meter run. The gas is measured and recorded and then at this point it is

sold, typically to an outside source or a midstream company. This is a cash

register for the producer that allows him to make money off the resource

that he's brought to the surface. A second valve that's related to the sales

line is what we refer to as the flare valve. The flare valve is installed in

case of maintenance on the sales line or in the winter time of a line could

possibly freeze or further on down the line they may be tying in a new well and

pressure backs up on the existing location. What the flare valve does set

at a higher setpoint than the sale valve if that pressure is met then this

valve opens up and sends all the gas that used to be sent to the atmosphere

it's now set to a combustor or a flare to be incinerated until the condition

changes. The fluid that drops back into the bottom of the two-phase vertical

separator is controlled by a liquid level controller in this case a float

ball connected to a mechanical linkage to a dump valve. As the fluid rises it

lifts the float ball in the vessel pushing down on the mechanical linkage

which then in turn opens the mechanical dump valve the oil the water and any

solids that might be in the liquid flow down this pipe into the dump line and in

this case the dump line could go to a couple of places – it could be go to a

final destination of a storage tank, but in this case the producer needs to

further process the emulsion in order to make it sellable. This emulsion line

will go down the dump line into another vessel and that vessel is called a

heater treater. The emulsion flows into the treater at the very top of the

treater is a baffle. At that baffle the gas, which again is lighter then the

liquid, breaks out of the top comes down this pipe, comes down to here – one valve

takes us to sales - the gas to sales - the other valve takes us to flare. Once the

emulsion enters the heater treater and the gas breaks out of the top, there

is a down comer that funnels the fluid to the bottom of the treater

and at that point the emulsion starts to break loose as a result of heat applied

to the process fluid. That process fluid then relaxes its molecules and the oil

and water separates more naturally by itself the oil being lighter and

gravity than the water will float on top of the water as it reaches a setpoint.

Oil spills over comes down the downcomer pipe and then you'll see another

Kimray valve - the treater valve. only controls the liquid in the downcomer

pipe it does not control the liquid inside the vessel as the height in the

downriver pipe meets its desired level the valve will come open the liquid will

leave the valve go down the pipe and into its final destination as crude oil

into the storage tank where the midstream company purchases crude oil

from the producer and then is taken to a refinery for further processing. As the

emulsion is being processed with the use of heat provided by the fire tube more

salt water will be produced in order to control the level of salt water in the

vessel the vessel comes with what we refer to as a water siphon. The produced

water then it goes up this pipe into what we call the siphon box or the weir

box there is a designated spillover point or a siphon nipple. As the water

reaches that level the water spills over, goes down this downcomer pipe and again

the valve controls only the level in the downcomer pipe. As the liquid comes down

the pipe, the valve will come open - will come down the pipe - and then will exit to

either a fiberglass tank for storage or it will go to the water treatment plan

on this location for further processing and then will be disposed of there.

This is a recirculating line - goes into the recirculating pump from here it goes

back to the inlet of the treater; runs through the whole treater again. So,

there's a line that we can bypass the separator, and then there's a line that

we can bypass the treater, and then there's a line that we can

bypass both of them. It's all done with valving.