DJI Mavic 3 - First Use Guidelines
In this video
we will show you how to use DJI Mavic 3 for the first time
Unboxing
Open the box and remove DJI Mavic 3 and its accessories
Downloading the App
You can scan the QR code on the official DJI website
or on the package to download and install the DJI Fly app
Preparing the Aircraft
Remove the storage cover
and unfold the drone’s arms
Introducing the Remote Controller
Remove the control sticks from the storage slots at the bottom of the controller
Extend the mobile device clamp
and you will find the RC cable
The cable on the right with an RC icon should connect with the remote controller
The other end on the left should be used to connect your smartphone
Take out the connector from the left and unwind it to the right
making sure it’s behind the non-slip pads of the clamp
The RC cable that comes in the box is a lightning cable
There are more connector options in the accessory kit
Place your smartphone inside the clamp
Tighten the clamp
with the charging port on the right side
making sure everything is secure
and then connect the RC cable to your smartphone
Powering On/Off
When using the battery for the first time
connect the USB-C port at the rear of the aircraft
directly to the battery charger until the battery indicators are on
which means the battery has been successfully activated
If the battery power level is at approximately 50% or below
we suggest charging it up to 75% or above first
so as to provide enough power for the upcoming activation
and firmware update
Press once
and then again
and hold for about two seconds
to power on the remote controller and the aircraft
If you want to turn off the aircraft and the remote controller
press the power button once
and then again and hold for two seconds
Activating and Updating
Launch DJI Fly and follow the instructions to activate the aircraft
A prompt will appear on the top left of the screen
if a firmware update is available
Tap the prompt to enter the update screen
and tap “Start Update”
During the update
do not power off the device or exit the app
After the update is finished
both the aircraft and the remote controller will remain powered on
Storage
Fold the aircraft arms
attach the storage cover
and store the aircraft in the Convertible Carrying Bag
You can also unfold the Convertible Carrying Bag into a backpack
which provides more space if needed
Preparing for Flight
Remove the storage cover
unfold the arms
and securely install the propellers
Check the power level of the intelligent flight battery
Launch the DJI Fly app
and it will automatically enter the live camera view
Tap “Safety”
and set “Obstacle Avoidance Action” to “Bypass” or “Brake”
and set the RTH height higher than the tallest building or nearby object
Flying Basics
Before flying
choose an open obstacle-free area
and place the aircraft on level ground with the rear facing you
Power on the aircraft
Check the battery level of the remote controller
power on
and set the RC mode to Normal
Check the flight interface in the app
confirm that there are no abnormal reminders
and that the GPS signal is good
Tap the Take Off icon on the left
and press and hold the prompt icon to enable Auto Takeoff
After takeoff
the icon will change to Auto Landing
Tap the Auto Landing icon on the left
and hold to make the aircraft land automatically
To take off manually
using Mode 2 as an example
Pull both sticks all the way to the bottom of the controller
and then push inwards or outwards
When the propellers start to rotate,
gently push the left control stick up to manually take off
The left control stick is for adjusting the aircraft’s altitude and orientation
The right control stick controls the aircraft to move forward, backward,
and to the left and right.
After you move the motors,
if the aircraft has not taken off,
push down the left stick to stop the motors
If the aircraft has taken off,
push down the left stick to land
Press the Flight Pause and RTH Button on the remote controller to make the aircraft brake
You can view flight distance and speed in the bottom left corner of the app
Keep the RC antennas facing the drone during flight for optimal transmission
When the GPS signal is weak,
the compass encounters interference,
or ambient light is not adequate for visual positioning,
the aircraft will enter Attitude mode and cannot hover or auto-brake
To avoid accidents,
please land in a safe location as soon as possible
Taking Photos and Videos
Tap the Photo button on the right and choose Photo, Video, or QuickShots
The camera parameter menu at the bottom right can be used to adjust parameters
You can also adjust the gimbal pitch and control the camera by using the gimbal dial on the left side
Use the switch button on the front to switch between photo and video modes
Use the shutter/record button on the right side to take photos and videos
Tap the Playback icon on the bottom right to view and download your footage
Advanced RTH
Tap the RTH icon on the left side of the screen and hold,
or press the RTH button on the remote controller and hold to initiate RTH
As long as the ambient light is sufficient for the visual sensing system to operate,
Advanced RTH will be automatically activated,
and the aircraft will plan an optimal flight route to return to the home point
Safety Precautions
Before takeoff, check if the flight environment meets all requirements, and set RTH altitude.
Don’t forget to check if the propellers and battery have all been installed securely,
Please note that the obstacle sensing system does not work in low-light environments or during night flight.
Always fly safely.
Attaching the Propellers
DJI Mavic 3 has two different types of motors (A/B) and propellers (A/B) that pair up
Attach the A propellers with the gray circle markings to the A motors with gray markings.
Likewise, the B motors without the gray circle markings should go with B propellers without gray markings.
Match the propellers to motors,
press the propellers down firmly and rotate to the lock direction
Remember to check that everything is firmly attached to ensure a safe flight
Thank you for watching our DJI Mavic 3 tutorial
First Use Guidelines
Enjoy your flight!