Hi.
I'm Mike from 1A Auto.
We've been selling auto parts for over 30 years.
We have a 19 millimeter socket, an extension and a breaker bar.
We're going to crack the lug nuts free.
Now we're going to raise and support the vehicle with a two post lift.
You can use a jack and jack stands.
Now with the vehicle raised up we're going to take the lug nuts off.
I'll pull the tire off.
This sway bar link is a little bit rusty, so we're going to spray some rust penetrant
on it.
We'll spray some rust penetrant on this nut right here.
We're going to take this nut off.
We're going to use a 17 millimeter wrench to get it on there, but when we loosen it
up this stud is going to start spinning so what we want to do is a little Allen in there,
a little spot for an Allen.
We're going to use a six millimeter Allen and I'm just going to hammer it in because
this one's a little rusty.
I'll take my ratchet and I'll put it on the tightening setting and then I'll loosen this
up.
This nut is on there pretty hard so what I'm going to use is a hammer and I'm just going
to tap on my wrench to get it started.
Just like that.
Then with my ratchet I'll hold the stud.
You can actually go like this to an extent.
This is pretty rusty.
I'm going to just use a wire brush.
Try to get some of this rust off of this stud.
Maybe that'll help.
All right, so this nut's giving us some trouble.
The next step, what you could do or what we could do would be cutting the stud off in
the back.
We could use a reciprocating saw or a Whizzer and get this stud cut.
Before we do that, I am going to attempt to use an impact gun.
What I'll use is some locking pliers on the back here first, just lock it onto the stud.
I'm just going to work the nut back and forth.
First I'm going to tighten it.
Now I'll just go back and forth.
This last time should take it off and there we go.
Got it off.
I'll pull the locking pliers off.
The lower nut for the sway bar link is right here on the backside.
The end is just as rusty as the upper one, so I'll take my little wire brush.
I'll just clean that off a little bit and spray a little more rust penetrant right here.
So to prevent my stud from spinning on this joint, I'm going to put some locking pliers
on the backside.
Pretty much what's happening I'm just putting it on that to prevent it from spinning.
I'll try to loosen this up.
I'm going to tap it with a hammer and see if I can get the wrench to loosen up a little
bit.
This nut wouldn't break free so we're going to heat it up a little bit.
Just going to use a little bit of MAPP gas.
This part of the sway bar link just popped off.
There must have been a nylon seal or something in there so that just popped off right there
like that.
Taking this nut off.
It's giving me a little bit of trouble but it's not impossible.
All right, so this nut's almost coming off.
If there was more room I could get a ratchet in there but really not that much room.
You could use a ratchet wrench to get this off if it wasn't so tight.
There we go.
Got it off.
This is our old sway bar link.
This is our new sway bar link from 1AAuto.com.
If you look at it, it's very similar.
The joints are the same.
The new one comes with new nuts.
Take those off.
This is generally what goes bad on these.
What'll happen is this will loosen up and this ball and socket will rattle when you're
going over bumps.
So get your new one at 1AAuto.com and you'll be ready to rock and roll.
All right, we're going to install the sway bar link this way.
Slide that stud in down below there and put the nut on into that.
I'll slide the upper stud in here and push it down a little bit.
Slide that in through the strut and snug that up.
I'm going to use a 3/4 ratchet wrench to snug this nut down and I'm going to use a six millimeter
Allen socket to hold the stud from spinning.
I'll stick my ratchet on there, just tighten this up and I'll put the ratchet on loosen
and that will hold the stud while I'm tightening it up.
All right, now we're going to torque this using a 19 millimeter socket and a torque
wrench.
I'm going to torque it to 59 foot pounds.
Kind of hard to do this.
The stud is just spinning so I'm going to just lock the backside of this stud with these
locking pliers.
That's 58 foot pounds.
Now I'm going to put the tire back on.
Line it up with the studs and I'll take our lug nuts and put them on.
It's easier to use the socket when you're putting the lug nuts on.
All right.
We're going to drop it down and torque them.
Now we're going to use a torque wrench and torque it with a 19 millimeter socket.
We're going to torque these to 80 foot pounds in a star pattern.
That is going to tighten the wheel properly.
Just like that.
Thanks for watching.
Visit us at 1AAuto.com for quality auto parts, fast and free shipping and the best customer
service in the industry.