John: Hey guys.
John here with realtruck.com.
Today I want to show you how to dress up your older 1999 Ford F250 SuperDuty.
Okay guys, you can see here we've got our fender flares out of the box.
They come with front and rear sets here and everything you need to put them on the truck
comes with all the rivets that you're going to attach on here, and also all your rubber
trim that you want to put on this.
And then I usually just take the screws and I'll start them by hand, just to get them
in the right place so that way we can adjust this and get it up on the truck nice and tight.
Okay, we've got our screws in, we've got our clips on so there you go guys.
All right, so we're ready to put this on and what we're going to do then is we're going
to take our clamp first and we're going to just put it over here where it's going to
go on, and then once we get this slid up on to the exhaust pipe here, we'll just take
our ratchet and socket and we'll tighten this down to hold this on so we don't have to worry
about it falling off.
There you go, quick, easy, cool upgrade to your truck and that's really how simple and
easy it is to install this Go Rhino exhaust tip.
The Spec-D projector headlights, they come with everything we need to get them installed.
We know everything's working so we're ready to put it back in the truck and we're just
going to lift her back up in here.
Got our top clips back in, we've got our screws replaced so what we're going to do then is
we're going to jump over and do the one on the other side.
It's going to install exactly like this one is.
We'll come back and let you guys see what it looks like when it's all done.
So we've got everything ready to go here to put our bed light in.
So what we want to do before we do that is take a rag with some isopropyl alcohol or
something along that lines that's going to clean this up and just wipe it down real good.
Peel back a little bit of our strip and we're going to start attaching it in here in our
truck bed.
You can kind of, because it is a rope-type style, you can pretty much do whatever you
want with it but we're going to put it in here nice and straight.
And so I'm just going to get it started right here.
And the best thing to do is actually if you want to keep it nice and straight is just
to peel a little bit of that tape at a time, the backing on it, and that'll help you keep
this in here without getting it all over.
All right guys, what we've done is we've gone ahead and ran our wires in through here to
the tail light, put the tail light back in, and we'll show you guys how the light works.
The Recon LED running lights.
What we're going to do with this one is we're going to center it right here on the doors,
so that way whenever you open the door the white light comes on and shines down onto
this running board to give you a little bit more visibility for getting in and out of
the truck.
So once we have it where we want it, then we'll go ahead and get this front part stuck
up here and then we'll just start peeling this tape out.
Access off road LED light.
We have our 4.3 inch round LED lights.
We also have the mounting brackets that go with them so you can install them.
Let's get this onto the truck.
Okay, once we have our mounting brackets in place then we can go ahead and attach our
light.
And we're just going to slide our light down here into the bracket, put our long bolt through.
At this point we can make up our mind whether we want to use the harness or if we want to
just go ahead and wire these up ourselves.
We're going to use the harness on ours which is, like I said, sold separately and get these
all hooked up and show you guys how it works.
As you can see here we've got our shocks out of the box.
They come with everything you need to get these on your truck.
That's how easy it is to put it together.
So let's get it on the truck now.
Let's go ahead and put it right up on here.
The Plasmaglow Fire and Ice LED tailgate light bar.
So we've got our light bar all hooked up.
We've got our wire ran.
We've got it all tagged up nice and neat under the truck, so the only thing left to do then
is just go ahead and take our four-way connector and plug it into our trailer connector right
here and it's all ready to go.