hey guys welcome to ERSBIT in this video i'm going to show you how to take off the screen
on the new iphone 12 pro in order to change it
if your screen is broken let's start by removing the two screws at the bottom of the phone
apple added a new ceramic shield on their new apple iphone 12 pro this year while removing
the screen on the new iphones i found that it's really difficult compared to the other iphones
the next step is to turn off the device
after that grab your suction cup
and just put it like i did the suction cup will help you
lift the screen in order to hit it evenly through the frame
also i'm using a heat gun because that's a really common tool that you can get and if you do not
have it a heat gun you can use a hair dryer but it's going to take more time than a heat gun
as you can see i started with the green guitar pick and it broke so i was in need to
re-hit the device because the glue apple has inside is really strong
so you will need a lot of round of heating up the display in order to have your first gap
using a hot plate is really efficient but if you do not know the exact time
that you need the phone to be heated up and the temperature that you need to put on the display
of the hot plate you might burn your lcd
using a heat gun is a little bit safer because you can direct the heat on the edge of the phone
where you have the frames because the glue sits on the frames if you have the frame heated up
in a good temperature you will get your first crack and you can start to lift up the display
also i'd advise you to put some gloves because the phone is quite hit up try to work slowly
and heat up the display and try to have your first gap between the phone and the frame it might
take you some time but be patient in order to not break the lcd also like i said in my other videos
try to not use a metal tool because you will scratch the edge of the phones try to stick with
plastic tools so here i have my first gap the tool was able to enter between the frame and the screen
after you have your first gap try to heat up the display more and work your way around
in order to widen that gap also if you find any kind of resistance while
lifting up the display add more heat and it will help you take out the screen safely
once the gap is wide enough try to put the tools in like i did and move your way around the
other part of the phone where the screen is still
glued to the frame and always use a little bit of heat and progress on lifting up the display
just go slowly and you won't break anything
so at this point i have 80 percent or ninety percent of the display is open
so you just need a little bit of heat again
in the top of the phone in order to heat up that glue that will let you lift up the screen entirely
work your way around slowly do not rush it
because you can break the flex cable or even crack the display
i'm not sure why it's been hard to lift up the
screen on this iphone 12 pro it might be due to the new ceramic shield
the ceramic shield look like it it has some good heatsink properties and using the heat gun was
a little bit difficult because you need to heat up a spot at a time in order to progress
as you can see the way to go with a heat gun is slow and progress
yes we have it open right now it's time to test the display and see if we've not broke anything
so turn on the device and check your
screen
the screen is not broken and everything is still working
perfectly
so this looks a little bit familiar
it hasn't changed much on the internals from the iphone 10 so let me show you what we have here
this is the motherboard then the screen and the haptic feedback and charging module in the bottom
we have the batteries the sim card tray
then we have the camera modules on the upper right
then we have the speaker the front speaker cable at the upper portion then
if you break the speaker flex cable your face id is gone there is no way to recover
the face id because in order to recover the face id you will need to solder some micro components
so do not break the face id cable which is attached to your speaker from speaker module
at this point while doing a screen replacement you need to be careful about the front speaker
flex cable that's the most important part that you do not want to break
so if you need to change your display on a new iphone 12 pro
you need to remove the screws on the cover of the motherboard remove all the screws
then remove the two flex cable that are attached to your display then
you need to also remove all the four screws at the upper portion that holds the speaker module
on the motherboard if you've removed all that then you need to transfer the speaker module in
onto the new screen then reattach everything the way you removed it that's basically it
these two cables are connected to the camera module
of your iphone if you break these cables your face id is gone it goes
for the same for the speaker cables if you break that also your face id is gone
so it's time to close the device
every year apple adds something that makes the repair on the new iphones
difficult in this year the camera modules are tied onto the motherboard and also
the screen are somewhat tight to the motherboard so if you break your screen
or camera it's really difficult to have it repaired and functional as normal
so before you close the screen onto the frame you need to add some glue around the edge where you
have the old glue and i'm using b7000 for the glue that i use regularly to seal the phones
after replacing the screens the one that i'm using right now is also b7000 using this
method try not to put too much glue on the phone when the aftermarket screens are out they will
surely come with some glue that's cut to match the frame of the phone so you will not need to use
b7000 to repair your screens because it's going to come with a pre-installed glue on the screen
when you think you've added enough glue it's time to close the
device
you
press gently on the corners you will hear a little popping sound
it means that the screen is entering the frame
then time to put the screws back in
then the last part is not mandatory you can use any kind of stuff that can apply a little bit of
pressure not too much because you risk to damage the screen just a little bit of pressure
on the edge of the screen against the frame of the phone and that way the glue will stick firmly
to the phone and the frame you do not need to use too much pressure just a little bit of pressure
to make the glue stick better
again after all that you need to test the phone
in order to be assured that you did not break anything
so that's everything the lighting the brightness the true tone display and all that
that is everything that makes the oem screens one of a kind
thank you guys for watching subscribe like and share i'll see you on my next
video