- VTEC just kicked in, yo!
- Oh, God!
- In the late 90s and early 2000s,
the import scene was super hot.
And it seemed like Civic,
S2000, and Integra GSR drivers
all wanted to make sure everybody knew
that their cars had VTEC.
So what are they even talking about?
What's kickin in when?
VTEC stands for
variable valve timing and lift electronic control.
It was invented by Honda engineer
Ikuo Kajitani in the late 80s,
and it's an ingenious way to make an engine
more fuel efficient and more powerful.
(clapping)
But those are opposites.
How does VTEC do that?
Let's brush up on some engine basics
about how air gets in and out of the cylinders.
So there's a head sitting on top of the engine block.
And all of the air needs to flow through it.
As the piston goes up and down,
it sucks air in and pushes it out
through intake and exhaust ports in the head.
There's these valves opening and closing those ports,
like tiny lids constantly popping off
and slamming back down again.
In an engine running at 4000 RPM,
the valves open and close 2000 times a minute.
A spinning camshaft controls the action
and timing of the valve.
There's cam lobes all along the length of the shaft.
When we say cams, what we're really
talking about are the lobe.
As the shaft rotates, the cams bump into things
that bump into the valve.
Different engines use different things for that.
Sometimes push rods, rocker arms,
or hydraulic lifters.
Some engines use a single camshaft
to control all of the intake and exhaust valves,
while others use separate camshafts
for each set of valves.
Single cam vs. dual cam.
The exact shape of the cam determines
when the valves open, how much they open,
and when they close.
For lots of complicated reasons, that camshaft
can totally change the personality of an engine.
Imagine we're running an engine extremely slowly,
like 10 or 20 revolutions a minute.
- That's impossible.
- But, at this slow speed, we'd want cam lobes shaped
so that, just as the piston starts moving downward
in the intake stroke,
the intake valve would open.
Then, the intake valve would close,
right as the piston bottoms out,
when the cylinder's full of air.
The compression stroke would happen,
and at the end of this, the exhaust valve would open,
with the piston at bottom dead center.
And it would close after the exhaust stroke.
But that's not what happens in an engine
'cause the RPMs are in the thousands.
The air's got momentum,
and there's a lotta other things going on
that screw with the air coming in and getting out
to help the engine run.
Leaving valves open longer, helps them maximize
the intake of fresh air and the expulsion of exhaust.
In earlier days, there's really only
one possible cam profile.
They threw in a camshaft with a
certain size cam lobes on it.
That got driven by the crankshaft,
and that was that.
But the cams that make the best valve timing and lift
for slow speed driving and good fuel economy,
well, they're horrible for making horsepower
and going fast.
Specially designed racing cams are big.
They open these valves sooner, close them later
than small cams would.
We saw in the turbo and nitrous episodes
that getting more oxygen in the engine
makes more power.
That little bit of extra hang time
gets in as much air as possible
and allows the cylinders to burn more gas
and make more power.
So big cams work really well at high RPM.
But they run like crap at slow speeds.
The tricks used to shove lots of air and fuel in
at high RPM are counterproductive at low RPM.
That causes messy, inconsistent air and fuel delivery.
You know that lopey idle that you hear from cool cars?
(engine idling)
That's because that car's got big cams.
(whistling)
Fuel efficient engine has small cams.
So the valves open just long enough
to get adequate power to get the car going.
- That sounds disgusting.
- They're limiting the amount of air into the cylinder.
So they also limit how much gas it needs to burn.
This is all fine at low rev.
But when the RPMs start to rise,
you're not able to get a whole lotta air.
So that's why cars built for good fuel economy are slow.
Ha, pfft.
Slow.
Most people aren't racing anyway,
so car makers usually settle on cam sizes
somewhere in the middle.
You can call that a campromise.
(laughing)
Okay.
This is where VTEC kicks in.
Honda figured out how to run a second cam lobe profile.
Basically, it's a fancy set of cams
that gives you the best of both worlds.
Fuel efficiency and power from the same engine.
If cams determine an engine's personality,
VTEC has a multiple personality disorder.
The Japanese market Integra came out
with VTEC in 1989.
And it first appeared in the US in 1991,
on the Acura NSX.
Japan taxes engines based on displacement,
so it made sense in Japan for automakers
to think of new ways to make efficient little engines
that could still pack horsepower.
Here's how it works.
Honda uses dual overhead cams.
And in a VTEC engine, larger cam lobes
sit between the normal-sized ones on the intake cam shaft.
Rocker arms are the middlemen
between the cams and the valve.
As the camshaft rotates, all the cams are bumping up
the rocker arms.
At low and mid-range RPM, the rockers that pair
with the standard cams are the only ones
actually moving the valve.
The bigger cam's rockers aren't connected
to any valves.
They're basically flapping in the wind.
So as you're cruising at 25 in a school zone,
the engine runs frugally,
using the moderate valve timing
set by standard cam.
When you hit the freeway on-ramp
and your right foot starts feeling heavy,
you want bigger cams and more horsepower.
The car's computer's been keeping tabs on everything.
And when it sees the right combination of
engine oil pressure, engine temperature,
engine speed, and throttle position,
it decides to grant your wish.
VTEC is go!
- Aaaah!
- The ECU shoots a signal to a solenoid control valve
that pushes the hydraulic pin
through normal cam's rockers
and into the big cam's rocker.
These locks those previously independent rockers together,
and, when the big cams hit, they push all the rockers
down and take over the valve control.
Now, the normal cams are the do nothing slackers,
while the bigger cams start opening the intake valves
sooner, opening them further, and closing them later.
Suddenly, you've got more air and more power.
When you let off the gas a bit,
and the computer decides you don't need
the extra grunt anymore,
the hydraulic pins retract to let the rockers uncouple,
and the engine goes back to running on the small cam
and just sipping fuel.
And now they have i-VTEC, which combines
multiple cam sizes with continuously variable valve timing
for even more performance.
Amazing.
- I was sleeping down there.
I'm a bunny.
- Guys, dudes, guys, dudes,
smash the subscribe button.
Thanks to Skillshare for sponsoring this episode.
I know you like learning,
and if you like learning, you'll love Skillshare.
Skillshare is an online learning community
with thousands of classes in design,
business, technology, and more.
You wanna know how we did this?
- Bart, I was driving.
- Then you can learn video editing
with Premiere Pro with Jordy Vandeput.
along with 6500 others.
Premium membership gives you unlimited access
to high-quality classes on must-know topics.
So you can improve your skills,
unlock new opportunities,
and do the work that you love.
Skillshare is also more affordable
than most learning platforms out there.
An annual subscription is less than $10 a month.
I've got that right here in my pants.
And what's even better, is that the first thousand people
to sign up with the link in the description
get the first two months for free.
So go to skl.sh/sciencegarage2
or click on the link in the description.
Go get skilled: Skillshare.
The more people who subscribe to Donut,
the more cool videos we get to do.
You can follow me @BidsBarto.
You can follow Donut @DonutMedia.
You wanna learn more about getting air in an engine,
check out this video on turbos.
You like VTEC, check out the up to speed
on the S2000.
Don't tell my wife about cam timing.