When you want a smooth transition from tile to floor coverings at lower elevations, especially
if you are using carpet, the Schluter-RENO-TK profile is a perfect solution.
Not only does the profile protect the edges of the tile, but it also has a channel beneath
the sloped flange that hides and protects the carpet edge.
RENO-TK is available in a variety of different materials and finishes.
Need to create curves in the floor design? In some materials, the anchoring leg of the
RENO-TK is available with a special radius perforation so that you can produce those
designs. All of these features make RENO-TK a great
choice for floor transitions to lower surface coverings.
We all know that planning is important with any tile installation. It’s even more critical
when working with profiles. It’s the key to a successful project.
In our demonstration, we will be installing tile adjacent to carpet.
We have selected the tile and profiles and determined the overall layout.
The RENO-TK will be installed to create a smooth transition between the tile and carpet.
The Schluter-DILEX-EKE movement joint will be used at the floor to wall transitions and
the inside wall corner. The tile base will be finished with the Schluter-RONDEC
profile. We selected the RENO-TK size according to
the thickness and format of the tile that will be used.
In addition to tile setting tools, we will also need to choose the proper tools to cut
the profiles. This will depend on what material the profile is made of.
We will cut the RENO-TK, in aluminum, using a miter saw with a non-ferrous blade.
If you will be using the stainless steel RENO-TK, it is best to use a variable speed angle grinder
set to the lowest speed with the PROCUT-TSM cutting wheel. The PROCUT-TSM can also be
used to cut aluminum profiles. A third option is to simply use a hacksaw
with a bi-metal blade. With the planning complete, let’s prepare
for installation. The floor is now ready for tile installation.
We have installed the Schluter-DITRA uncoupling membrane where the tile is going to be set.
The RENO-TK profiles are installed at the same time as the tile.
This sequence may vary. It depends on your layout and installer preference.
First, measure where the RENO-TK will be installed. Then, transfer the measurement to the profile.
Keep in mind that we must avoid any overlap of the profile anchoring legs because this
will interfere with the tile installation. We make miter cuts to produce a clean transition
between the RENO-TK profiles. Be sure to observe all safety instructions
and standards. We cut the RENO-TK using a miter saw with
a non-ferrous blade. For best results, cut the profile slowly.
An accurate cut ensures a clean transition. Then, file the cut end of the profile to remove
any burrs. Dry fit the profiles.
Next, we cut the DILEX-EKE, keeping in mind that we must avoid any overlap of the adjacent
profile anchoring legs. Now we can move on to the installation.
Using a notched trowel, apply thin-set mortar to the area where the first section of the
RENO-TK profile will be installed. Firmly press the anchoring leg of the profile
into the thin-set mortar and align. The next piece of RENO-TK is installed the
same way. Take care to align the profiles, paying close attention to the area where the
profiles meet. Next, we trowel additional thin-set mortar
over the anchoring legs. This is necessary to ensure full coverage and support of the
tile edges. Solidly embed the tiles into the thin-set
mortar, so that the tiled surface is flush with the top of the profiles. The profiles
should not be higher than the tiled surface, but rather up to approximately one-thirty-second
of an inch or one millimeter lower.
Set the tile up to the integrated joint spacer. This will provide a uniform grout joint.
If you are using the RENO-TK in stainless steel or brass, there is no integrated joint
spacer, so you will need to leave a space of approximately one-sixteenth to one-eighth
inch. Don’t forget to clean any excess setting
material immediately from the profile to avoid any damage to the finish.
We complete the installation by setting the remaining tiles.
As you can see, the RENO-TK is the perfect solution when you need to protect tile edges
and provide smooth transitions to carpet. Another great innovation from Schluter®-Systems!