Hey, Zoo fans. In this video we're gonna go over how to set up and maintain Zoo Med's Nano 30. The Nano
30 is an External Canister Filter that's designed to help maintain clean water in aquariums. This
filter combines mechanical, chemical, and biological filtration to efficiently clean up to 30 gallons
of water. Before starting, review the included instructions to make sure that all the parts
of the filter are included. Once everything is accounted for you can begin setting up the filter.
We'll first start with putting together the filter's Water Intake Unit. Find one of the two Hard Elbow
Units. Screw the Screw Nut onto the threaded pipe and attach the Intake Tube to the non-threaded
pipe of the elbow. The Intake Tube is the clear plastic tube that does not have irrigation holes
down the side. Next, snap the Intake Strainer and Adapter together, and attach both to the
opposite end of the Intake Tube. Lastly, add the Suction Cup Clips to the Intake Tube to apply the
Suction Cups to the Clips. Simply press and twist. Next, we'll put together the Outlet Unit. Screw the
Screw Nut onto the threaded pipe of the second Hard Elbow Unit and attach the small Elbow Piece
from here you have the option of attaching the Spray Bar or Flow Diverter. When attaching the
Spray Bar, add the two Suction Cup Clips and plug the opposite end of the tube. Once you've set up
the Intake and Outlet Units you can begin assembling the filter. Start by attaching
the four Rubber Feet to the bottom of the filter. After that, open up the unit by gently pulling on
the clasps on the side of the filter, and pressing down to push the head of the filter up. Once you
have the unit opened, remove the Filter Sponges. Rinse the Sponges, Carbon Bag, and Ceramic Media
under running water to remove any dust or debris. Place the Side Filter Sponge into it's appropriate
chamber, and then place this square Center Filter Sponge in the center chamber with the hole facing
upwards. Place the Carbon Bag in the bottom of the empty chamber. Take note that the carbon should not
be removed from the bag. Add the Ceramic Media on top of the Carbon Bag. Lastly, make sure the
Intake Strainer is attached correctly to the Impeller Cover and that the Air Vent Tube on
the Filter Head is pointed upwards. Fit the Filter Head back onto the unit making sure the Fill Cap
is over the chamber with the Ceramic Media. Secure the clasps on the side of the canister, and your
filter is now ready to install. For installation, situate the Intake and Outlet Units the way you
want them in your tank. Secure the Suction Cups to a clean smooth surface. The Intake Strainer should
be completely submerged in water. Positioning the Spray Bar just above the water surface will create
surface agitation and increased oxygenation. Screw two Screw Nuts onto the threaded pipes on the Hose
Connecting Device. Place the canister on a flat surface near the tank and attached the two clear
Rubber Hoses the Intake Hose should connect to the 'IN' Pipe on the canister, while the Outlet
Hose should connect to the 'OUT' Pipe. Once the hoses are in place, tighten down the Screw Nuts
on the end of each hose. Make sure there are no kinks in the hose. Hoses can also be cut shorter
if needed. Now that the filter is ready, remove the Fill Cap on the top of the filter and fill
the canister with dechlorinated water. Replace the cap and make sure it's secure. Now plug the
filter in, and it should instantly turn on. For safety reasons, it's recommended to have a drip
loop. Do this by letting part of the filter's cord hang below the power outlet. The water flow can be
adjusted by changing the controls on the Intake and Outlet Elbows. Your filter is now ready and
operational. This Filter should be cleaned at least once per month. For maintenance purposes,
always disconnect any electrical appliances being used with or around the tank. Rotate the
Hose Connection Device to the unlocked position to easily remove the Intake and Outlet Hoses
from the canister. For regular cleaning, take the Filter Head off and remove the Sponges and Carbon.
Clean the Sponges under running water to remove as much debris as possible. Rinse the Ceramic
Media in dechlorinated water, and replace the Carbon Bag once every three to four weeks. From
time to time you'll want to remove and clean the Filter Strainer and Impeller Cover. The cover can
be removed by gently pulling up on the tab. Next, remove the Impeller by pulling up on the small
metal shaft. Clean both the Impeller and Impeller Chamber. Once finished, return all the parts to
their appropriate positions, and make sure each one is fastened correctly. If they aren't appropriately
fastened, the Filter may not operate. Lastly, make sure the Air Vent Tube is pointing upwards. Lock the
Filter Head back on the canister, and then connect it to the Hose Connecting Device by twisting it to
the lock position. Fill the canister with water through the Fill Cap and replace the cap. Plug the
Filter in and your Filter should now function like new. That's all for now, see you next time.