Welcome to HowFixit and in this video, I will show you how to replace charger port on the
iPhone 11 Pro Max What tools you needed to disassemble the iPhone
11 Pro Max: Screwdriver set
Plastic mediator Suction cup for removing display
Tweezers Plastic opening tool
Adhesive tape for restore water protection and Adhesive silicon tape for the battery
In the description under the video, you will find links where to buy all these tools and
replacement parts for iPhone 11 Pro Max To replace the charging port in the iPhone
11 Pro Max, you need to unscrew a lot of screws that have different sizes, but the most difficult
thing is that you will need to assemble everything back and each screw must be fasten into right
place.
Therefore, I recommend using a magnetic mat and laying out each screw step-by-step during
disassembly.
Turn off your iPhone before starting disassembly.
Remove the 2 screws near the lightning port with a 0.8mm Pentalobe screwdriver.
Take a hair dryer and heat the display surface for 1-2 minutes at a temperature of 60-70
degrees Celsius.
Fix the suction cup on the bottom of the display and pull the ring up until there is a gap
between the display and the housing.
Insert mediator and disconnect the display from the iPhone case on all sides.
At the top of the iPhone, do not push the mediator much into the case, so as not to
damage the elements from the face id module.
The case opens like a book - the display to the right.
Remove the 2 screws on the small panel and 6 screws on the large panel.
First, disconnect the battery cable and after 3 cables of the display.
Remove the 4 screws and remove the panel.
There is a second battery cable under the metal panel, first turn it off and then disconnect
the Taptic Engine cable.
Remove 2 screws with a Phillips screwdriver and 1 screw with a 1.5 mm Standoff screwdriver.
Now you can remove Taptic Engine from the housing.
Remove the 3 screws on the metal panel, then remove it and disconnect the cable from the
iPhone main board.
You don't need to remove the battery, I did this for other video instructions.
Lets begin to remove the bottom speaker, remove 2 screws with a Phillips screwdriver and 1
screw with a Standoff screwdriver - 1.5 mm.
In the iPhone 11 Pro Max, the bottom speaker glued to the case and, if you want to keep
the factory adhesive tape, heat the surface of the speaker and unstick it from the case.
Remove the screw and remove the metal panel, it's also glued, so use a hair dryer again.
Remove all the remaining screws
on
the bottom.
Now let's begin to the removal of the cable with
the charging connector.
This cable glued to the case, so you need to heat it with a hairdryer and at the same
time unstick it from the iPhone case.
The cable removed and if you did everything carefully, the factory sticky tapes will remain
on the back housing and you can reuse it when reassembling iPhone.
In the description you will find a link where to buy a new cable with charging port for
iPhone 11 Pro Max.
In the process of assembling, be careful with the types screws, rest just repeat by
the video.
The iPhone 11 Pro Max assembled and now you can connect the display and check how the
smartphone works before final assembly.
To check the iPhone, just connect 3 display cables and a battery cable, but only in that
order, first the display cables.
Check how iPhone works and If all the functions work fine, you can begin to the final assembly
of the iPhone with the restoration protect against water and dust.
Remove the silicone adhesive tape from the iPhone back housing.
Using isopropyl alcohol and a cotton swab, you can wipe the back housing, this is not
necessary, but it will not be superfluous.
Before attaching a new adhesive tape, make sure that you glue the right side on the back
housing.
This silicone tape restore resistance to water and dust.
This doesn't provide 100% waterproof for your iPhone but without this sticker, the display
will not hold well and dust will get inside the iPhone.
In the description you will find a link where to buy such a sticker.
Press the sticker on top, so it sticks better to the case.
Let's begin to connect the display.
First, connect 3 cables of the display, then the battery cable, and only in this order.
Install the panels and fasten the screws.
Turn the display over and push it to the case.
Fasten the 2 screws near the lightning port and you can turn on iPhone 11 Pro Max.
That's all, I hope this video was useful for you and I helped restore your iPhone 11 Pro
Max.
See you soon on HowFixit.