Today I'm going to show you how I made this Piggy Bank for my daughter Caity. She absolutely
loved it. It's definitely a great project to make. We do sell the plans for this on
our website with all 26 letters, so definitely be sure to check that out. There's a link
down in the description. Without further ado, let me show you how I made it.
Sticking down some acrylic to the Stepcraft M1000 CNC Machine to start a new project to
make a Piggy Bank for my daughter. We do have the plans available for this on our website.
So definitely check those out there. Includes all the letters A to Z. It's definitely an
awesome plan and an awesome project. So definitely check that out.
Using the 45626-K 90 degree v-bit to carve my daughter's name into the acrylic. A lot
of people don't think that you can v-carve acrylic, but I'm here to tell you that you
definitely can. This bit did a great job going through here at over 60" per minute and doing
a really great cut without melting the acrylic which is really nice to see.
You can see there a little bit of fuzz is there on the protective paper for the acrylic,
but that's just a cosmetic thing of the paper. It cut the acrylic beautifully and couldn't
ask for it to do a whole lot better.
If you love this type of content, be sure to subscribe to our channel and go ahead and
hit that bell so that you'll be notified on all of the new videos when they're released.
Also, don't forget to follow us on Instagram @toolstoday.
So next, we're gonna go through and chamfer out where we are adding the screws later on.
This will countersink the heads below the acrylic and we'll drop that off and pick up
the 51411 1/8" diameter Spiral O Flute bit and this will go through and it will pocket
out for the holes for where the screws are going to go through.
After that's done, we'll go drop it off and pick up the 51404-K ¼" Spiral O Flute up-cut
bit to go through and cut the profile on the acrylic. We went through here at a ¼" depth
for a pass. So, cutting through the acrylic in a single pass and this thing did an absolutely
amazing job cutting through this acrylic.
It went through without melting it all at over 100" per minute and did a great job with
a beautiful finish on the edge. Couldn't ask for a whole lot better there. And you can
see what that looks like right here. So anyways, that is done.
So now we can turn our attention to the wood. I clamped in a block of solid oak here up
against the Stepcraft work holding wasteboard. We do sell the plans for that on our website
as well. And then using the 46415-K 1/4" down-cut bit, we're gonna go through and cut the coin
slot here. I applied Oramask to this project, just so that you can get a visual on film
of all the different cuts that we're making so it makes it easier to tell what we're doing.
So now we're going through here. We're going to cut the slot for where the acrylic will
sit on this project. So, we're gonna go through and get all of that done. The down-cut action
in this bit leaves a beautifully clean top surface, which is exactly what we want to
see throughout this project. So now we're gonna go through and pocket out the insides
of the letter. And this is really cool to see it acting kind of like a Pac-Man, going
through here just munching off bits of wood at a time. It's definitely really, really
cool to see. So, we're gonna go down a full inch on this piece here. So that way we have
plenty of room for the coins. And you can see that bottom surface finish is spectacular.
Definitely really nice to see that and all of the big chips that we have from cutting
that.
So now we're gonna go through and do the outside profile of this letter. We're gonna go through
in four passes to reach a full 1" depth of cut. And you can see again, that down-cut
action of the bit forces those chips down, which leaves a really nice clean top surface.
Using the 46233-K 1/16" down-cut bit, we're going to cut in all of the screw locations
for where that acrylic is going to mount that we drilled out in the acrylic earlier. It
went through in three passes drilling just as much as the bit can handle. And now that
that is done, you can see the acrylic piece fit in there really nice, definitely nice
to see that. So, this material is thicker than we're able to cut on the CNC with the
bit that I was using.
So, we're moving over to the bandsaw to cut the remainder of the material here. I find
it easier to do this than trying to flip it over on the CNC and get everything lined up.
Moving over to the router table, I'll use the 47090 1/4" diameter Flush Trim Bit to
just take all of the rest of the material off and flush everything up nice and smooth.
After that, I'll use the MR0110 mini round over bit. This bit has a 3/16" diameter ball
bearing. You can get it into all of the tight locations cut out by the bit. It also leaves
a small 3/32" Radius Round Over and it does a great job just kind of easing that edge
over for a nice, smooth finish.
So now that that is done, I'll just extend those holes down using a drill bit that fits
the size of screws that I'm using and then I'll just sand over the edges to make sure
that nothing is sharp.
So now that that is done, we can go ahead and sign the back just like I do on all projects
that I make for Caity and add a little note for her. I finished this piece using some
Minwax Spray Lacquer in satin and it did a really nice job bringing out the color of
the oak. Now that we're at the end of the project, we can take off the protective paper
on the acrylic and get that fully installed on the piece.
The sounds here of it popping are so satisfying. And it's definitely really nice to have a
nice tight fit there. So, we'll get everything nicely screwed down and this piece is coming
to a close. We will get everything wiped off and we are now ready to go give it to Caity.
This is definitely a project that I love how it turned out and hopefully you guys enjoyed
watching it but I will let Caity do the sign off here. Hopefully you guys enjoyed it. Have
a great day everybody.
Hey Caity?
Caity: Yeah.
Matt: I got something for you.
Caity: What?
Matt: I got you a new Piggy Bank. So, what do you think these are? You know what letters
those are?
Caity: C-A-I-T-Y.
Matt: Yeah. What does that spell?
Caity: Caity.
Matt: Do you like it? Yeah? You want to put some coins in there? All right, let's do it.
And I definitely think your Piggy Bank needs a few more coins. What do you think?
Caity: Ahh…
Matt: There you go. Let’s put all those in there too.
Caity: I got coins.
Matt: Do you?
Caity: Yeay!
Matt: What do you do with coins?
Caity: Getting stuff with it.
Matt: What do you buy? What things you like to buy?
Caity: Toys.
Matt: Toys?
Caity: Yeah.
Matt: Yeah. You do like toys.
Caity: Lots of toys!
Matt: You like how the coins move in there?
Caity: Thanks for watching. Have a good day! See ya! I love my PIGGY BANK.
Matt: Thank you guys so much for watching. If you love this type of content, be sure
to subscribe right over here. And for more great videos, click right over here.