Friends, a big hello to everyone today, let's work again with the remnants of foam, what happens, let's watch
the video, I still have these, again, from household appliances, I collected the foam plastic in a bag
and don't throw it away, I want to experiment to show you
today we'll work with different solvents, acetone, xylene, and in the end, we’ll paint the table, so let’s go,
for starters, let’s do a little experiment with you, what does the foam plastic dissolve and what doesn’t
I have such acetone, technical acetone, ordinary, xylene, solvent 646, we
’ll collect a little bit into the first container of xylene, just a little bit a little solvent acetone and
technical acetone let's start with xylene perhaps in small straight pieces the reaction is everything melts
right in a small piece now the solvent reaction is bigger and faster
acetone melts faster, even faster and technical acetone as you can see there is no reaction in it at all unfortunately
it does not melt at all does not decompose into atoms many wrote why I am
trying to dissolve in acetone melt dissolve the foam and it does not melt, as you can see, it is a
fake of some technical kind, it is not clear what it is made for, it says on it that it is added only to
paints and varnishes, we have ordinary acetone to dilute nitro varnish nitro paints
nitro enamels, that is also for diluting paints, but as you can see, the difference is
this acetone, we remove it to the side, as we see, it’s useless for us, let’s do it like this, three of our
patients, I made about three identical ones like this under the rectangle and let’s try which
one will melt faster and lower it by one-two-three and let's see who melts faster anyway
1 acetone coped
, as we see 2 there was a solvent and in last place we have xylene, as we see here, it turns out a
white precipitate, there is practically no sediment, only a small foam, and
also in xylene there is also a small foam, also no sediment no, I want to say that
it’s good to do it in acetone if you make some kind of glue, that is, it can be made thick thick
by viscosity in from this, I think it will be a good glue, we
will try to apply it on a porous coating later, just now I will make a homogeneous
homogeneous substance with a solvent, I will see what will happen to it with 646
worse and worse dissolves at this stage of it and leave such a homogeneous mass turned out to be
liquid took a piece block foam and marked it now, first we apply acetone once and apply it directly with a stick in
a thick layer, and tomorrow we will try, leave it to dry, try to pick it up, pour it with water and see
what this substance is like, how it picks out how it will hold on, but
I think that’s enough, but on this side with solvent 646 we will pour xylene we will use xylene
in another place we will use xylene with wood and with dye and leave it now to dry
until tomorrow and tomorrow we will see for xylene I have prepared a little more container and
also melt our foam 1 of course you can see it very well how do you corrode the first pieces
straight tricks
well, then decay starts worse but we’ll finish it until we reach our desired consistency
, it’s already become an opaque liquid, I won’t add more, I think that’s enough
now I’ll take a universal color scheme and drip a little of it there
, we’ve got such a liquid, I have such a table, it’s old and already a long time ago for a long time it
was all black, it was used by the builders, but I decided to update it,
I’ll try to apply our composition and see what comes of it, it’s
applied very well with a brush, at least
as you can see, I’m pouring it straight in bold and bold to soak all the pores and all the cracks
, we covered the whole table, leave now it
was very interesting to dry to cover the OSB and paving stones now we’ll just apply and let’s also leave it to dry and tomorrow we’ll see
beforehand I didn’t primed anything, didn’t clean anything from dust, as you can see, there’s even sand,
I think it will be interesting to everyone, including me, what will happen to we will also apply our solution to the metal with a metal , we
will cover it completely, it is not cleaned, not degreased, just that's how it is we’ll leave everything to dry
friends, as you can see, the table dried up, it dried up yesterday, you couldn’t wait, it probably took more than
15 hours, but it dried up yesterday in just three hours, it was already dry, but it’s true that because it stood
in the sun such a rough truth, the surface turned out a little well what I tried to
carry to the mermaid and it turned out to be a little bully, for which I would make it so that it does not stand on the street
and just be like a workbench, look what happens to the water, as you can see, the water rolls down
, that is, you can see that the water immediately rolls down and leaves, that is, the table is protected now from moisture
, that is, protection for wood, impregnation is very good water, it doesn’t absorb into the
wood, it just rolls off the main thing is that now you can’t drive splinters because after all these are
glued parts, they were poorly polished because the fibers are directed in different directions, it
was even possible would depend on bringing in the splinters, they are obtained from our varnishes list, the table looks solid, I don’t know
how it can be used both for food, then the EU I don’t think it’s likely to cut something food on it
, but as a protection for outdoor steel for outdoor coverage, for a workbench, the very thing was
taken out into the street by all the test subjects here we had a solvent film so transparent dense and acetone, acetone is more matte
let’s try how they behave with water, I think that there are one hundred percent water-repellent properties, well, as you can see, the water has merged here where it was not soaked, of course, it is absorbed here,
but what we have in terms of strength, look, you need good strength to poke around until the block, but that is, of course,
this is not protection it’s kind of straight, but it’s difficult to get to the block, solvents, what about acetone, and well, acetone is worse
, you see it peels off together with the foam block, that is, on acetone on porous surfaces it
behaves
worse when exfoliating, but the solvent, as you can see, showed itself very well the next block , also painted with our paint that was made, let's try it right on the table, as you can see, everything is also
not absorbed, the block is completely dry curb stone I was also covered, I think
you can also safely pour water on it, and yes, it also leaves water, nothing will be absorbed, that is,
as protective water-repellent properties take place, but I do the most interesting OSB right on the table because
I’m not afraid that it will get wet now wipe and everything,
that is, OSB, although it is moisture resistant, so it’s clear that the water also rolls off, well, let’s see what we have with the metal-coated
listen, well, of course it sags, but
well, since the protective one can and can be used as protection, that is, a
little Of course, there are carabiners, now look at the table as you can, just took some water,
drained everything, the water did not fit in with a cloth, wiped it
and the table can be said to be almost dry and did not absorb any moisture
, friends, but I hope that the video was at least something useful to someone interesting , here we have such a video today with experiments
with a small one and also repaired and restored my workbench, I want to say a huge thank you to you
for watching me that you are obligated to support write your opinion carefully and I try
to answer all the comments for the first day, then I just get lost in the comments, sorry, but on the first day I
try to answer everything as much as possible, so once again thank you so much I wish you all
good good health all the best but also all the very best good, do not forget
to write a comment, like it, but I say goodbye to you, until we meet again, bye bye