We talked about crane failures in a previous video, but you might be surprised to learn that
things can and still go wrong with heavy lifts even when the crane is perfectly safe and sound.
All cranes use a hook as a connection to the load, and yet, few things we need to lift have
an attachment that fits nicely over a gigantic steel hook. “Rigging” is the term used to describe
all the steps we go through to attach a load to a crane so it can be suspended and moved.
And, like all human endeavors, rigging is prone to error. Some of the most serious crane failures
in history had nothing to do with the crane itself but were actually a result of poor
rigging. One of the worst construction accidents in U.S. history happened in New York in 2008
when a large metal component of a crane was improperly rigged. The overloaded slings failed,
dropping the collar directly onto its attachment points to the building under construction,
causing it to detach and collapse. Six workers and one civilian were killed in the incident,
and many more were seriously injured. There’s a lot that can go wrong below the hook,
so in this video, we’re going to take a look at a few of the fundamentals in attaching and securing
a load and some of the hidden hazards that can pop up if not done properly and carefully. I’m
Grady, and this is Practical Engineering. In today’s episode, we’re talking about rigging.
You’ve probably heard the phrase that if your only tool is a hammer, every problem starts to
look like a nail. It’s a lighthearted way to warn about over-reliance on a familiar tool.
But, if you’re a rigger whose job is to secure loads to cranes for lifting,
you really do have just one tool. You don’t use a piece of old rope out of your pickup bed.
You don’t use a ratchet strap from the big box store down the road.
And you definitely never use the crane’s hoist line to wrap around a load. You have one option:
a sling. Of course, slings come in a wide variety of sizes and types and materials,
and you also have hardware like hooks and eyes and shackles and pulleys but, yeah, one main tool.
And here’s why. Slings have a rated capacity. That rating is a guarantee from the manufacturer. More
importantly, it’s a big responsibility taken off the shoulders of a rigger to know and trust that
each connection to a crane or hoist can carry the right amount of load. So what do these tags mean?
It’s actually pretty straightforward. The tag shows how much weight you can put on the sling
using the three basic hitches. If your load has a hook or a shackle, you can use the vertical hitch:
one eye over the load and one eye over the hook of the crane or hoist. It’s the most straightforward
configuration for a sling and takes full advantage of its load capacity. If there is no attachment
point on your load, you might instead use a basket hitch. In this configuration, the
load is cradled by the sling, and both eyes are on the hook. One benefit of the basket hitch is that
it doubles the sling’s load capacity since you have two legs holding instead of just one. But,
it only works if the load is balanced and easy to control since it’s only cradled from the bottom.
If you need a snug grasp on the load, you might use the third basic option:
a choker hitch, where the sling passes through one eye and attaches to the
crane hook on the other. The choke point has extra stress when used in this configuration,
so the load rating for a choker hitch is less than that of the vertical or basket hitch.
If you’re using a sling to lift something heavy and don’t see a load rating tag,
just stop. Every sling rated for rigging has to have a tag, whether it’s a synthetic
sling like this, a wire rope, or a chain. Even so, the vast majority of rigging failures
happen because a sling was overloaded. You might be wondering why that’s the case when
the load rating is spelled out right there on the tag. But those three numbers hide quite a
bit of complexity involved in rigging, and I have a few examples set up here in my garage
to give you a glimpse into those intricacies. Even if you aren’t planning to connect a 20-ton beam to
a crawler crane any time soon, this information applies to lifting just about anything.
The first rigging pitfall is center-of-gravity. Not all loads are evenly distributed or equally
balanced, and that can cause some serious issues if the rigging doesn’t take it into account.
For example, if you’re using multiple slings to lift something, your first inclination might be
to simply divide the total weight by the number of slings to estimate the load each one will carry.
But if the slings aren’t all attached at the same horizontal distance from the load’s center of
gravity, the total weight won’t be distributed evenly between them. That may seem obvious,
but many many loads have been dropped because of misunderstandings with center-of-gravity.
For just one example, loads often show up to a site in a crate where it’s not
quite so easy to see how the weight is distributed. In a worst-case scenario,
incorrectly estimating the force on each sling may cause one or more to overload and fail. But even
if the sling doesn’t give out completely, it might stretch just enough to cause a load to shift.
And if it shifts such that the center of gravity moves to the wrong side of the attachment points,
there’s a chance it will tip and fall. You can’t push a rope, after all, so slings
only provide resistance in one direction. So when lifting a load that isn’t equally balanced between
attachment locations (and especially for the big lifts that use more than one crane), you have to
calculate the load share between the slings and make sure each one can handle its portion. The
formula is super simple as long as you know the center of gravity. And, if there’s a chance a load
could slide if one sling stretches more than the others, it’s got to be secured before the lift.
The next potential rigging pitfall is the sling angle. Let me show you an example:
Say you have a balanced load, and you need two slings to attach it to a crane,
but your slings are kind of short. So, when you get everything hooked up, the connections make a
30-degree angle from the horizontal. Is each sling carrying half the weight of the load? Would I even
be asking if the answer was yes? In fact, at a 30-degree angle, each sling is subject to double
the force that it would otherwise feel if it were perfectly vertical from the load. Why is this?
Slings can only pull in one direction. For simplicity, we sometimes divide the force
in the sling into its vertical and horizontal components. If the sling is perfectly vertical,
it has no horizontal part. But as the angle of the sling changes, the horizontal component
becomes a greater and greater proportion of its total load. This may not need to be said,
but we don’t need a horizontal force to lift something. We need a vertical one. In fact,
the horizontal force isn’t just unnecessary, but it also has to be canceled out by an equal
and opposite force in the other sling. So, the shallower the angle of the sling,
the harder you’ll have to pull on it to get enough vertical force to lift the load.
Watch the spring scale as I change the angle of the slings holding this steel bar. It’s a little
hard to read on camera, but it’s still clear what’s happening. When the slings are vertical,
each one holds half the weight (in this case, about 800 grams each). But as I bring the tops
of the slings toward the center (like they would be if attached to a single crane hook),
you can see the plunger of the scale descending. When the tops of the slings touch, the scale reads
about 1200 grams, an increase of about 50 percent. I’m sure you can imagine what would happen if you
incorrectly divided the weight of the load by two and assumed that to be the force in the slings.
You’d be underestimating by quite a lot. So, when using slings that aren’t vertical,
you have to apply a reduction in capacity based on the angle.
Again, the formula is simple, but you have to know how and when to use it.
Shallow horizontal angles aren’t just an issue with sling tension, though. Those horizontal
components of force that I mentioned have another disadvantage related to the third and final
rigging pitfall I want to discuss: abrasion. As I said, slings can be made froma few materials,
including chain and wire rope, but one of the most common materials is woven synthetic fibers
like nylon and polyester. These synthetic slings have a lot of advantages. They’re lightweight
and easy to move around. They don’t create sparks that can be dangerous in industrial environments.
And, they’re soft, so they won’t scrape or damage whatever they’re connected to.
But, they have disadvantages too - mainly that synthetic slings are more susceptible to abrasion.
Those horizontal forces I mentioned earlier don’t just increase the sling tension beyond the
weight of the load. They can also cause a sling to slide. Obviously, that’s an issue if they slide so
far that the load falls. But even if they don’t, the friction with the load can lead to abrasion
and even failure of the sling. Synthetic materials are much easier to cut than wire rope or chain,
so they have to be protected from sharp edges, corners, and burrs. Synthetic fibers
can also melt. You might not think that a little sliding would generate much heat,
but consider that friction is a function of the contact pressure between the two surfaces.
These slings are pretty small compared to the weight they carry, meaning the pressure they
exert can be enormous. Watch what happens on the thermal camera when I pull down on this loop as
it slides along the pipe. Even a small amount of sliding under so much pressure can create
enough heat to melt the fibers. One way to avoid the possibility of sliding is to use a spreader
bar - a device that helps distribute the singular lifting force of the hook among attachment points
that can be further apart. This kind of device lets you reduce the angle of your slings,
giving them more capacity and reducing the possibility of them sliding and abrading.
I’ve been referring to “you” a lot in this video, putting you in the shoes
of a rigger learning the ropes. But I just want to clarify that this video is not for training.
If this is your first exposure to the topic, I hope you’ll agree that you’re not ready. Rigging
is a vital but dangerous job, so if you’re going to be involved in any heavy lifts,
there is a lot more to learn than my examples in this video. Finally, if you enjoyed this one,
check out the companion video about crane failures and what can go wrong above the hook.
Hey, the fact that you stuck around to the end of this video means that you’re pretty
thoughtful about the kind of content you spend your time enjoying. In other words,
you probably prefer learning new things about the world more than run-of-the-mill
television programming. You probably also don’t enjoy watching ads like this one, which is great,
because Nebula doesn’t have any. Nebula is a streaming service built by and for independent
creators like MinutePhysics, Real Engineering, Wendover Productions, and a bunch of others
(including me). It’s a way for us to try new ideas that might not work on advertiser-supported
platforms like YouTube. My videos go live there the day before they publish here,
with no ads or sponsorships. And, we’re super excited to be partnered with CuriosityStream,
a service with thousands of documentaries and non-fiction titles on pretty much every subject
you can imagine. CuriosityStream loves independent creators and wants to help
us grow our platform, so they’re offering free access to Nebula when you sign up at
CuriosityStream.com/practicalengineering. I know there are a lot of streaming services right now,
and all those monthly subscriptions can be tough to keep track of. That’s why this bundle is such
an awesome deal. CuriosityStream is taking 26% off an annual plan - that makes it only
$15 for an entire year of access to thousands of thought-provoking documentaries on CuriosityStream
AND everything on Nebula as well. You can watch awesome big-budget content on CuriosityStream.
I love nature documentaries, and this special called Wild Galapagos narrated by Mike Rowe
is one of my favorites. Or, watch Tom Scott pit other YouTubers against each other in his
Nebula-exclusive gameshow, Money. It’s a great way to support my channel and a whole host of
your other favorite educational creators. Plus it’s just a great deal. Do us both a favor and
click that link in the description. Thank you for watching, and let me know what you think!