Installing your ENHET bathroom
Preparing the room
Prepare the room
by making sure your walls and floors are even
and suitable for supporting the bathroom furniture
Make sure that the tiles
pipework and electrical outlets are in place according to your plan
You may need professional help in order to meet the plumbing
and electrical regulations in your country
Now check the walls to make sure that
they’re strong enough to support your bathroom furniture
Find the highest point of the floor and mark it on the wall
This is the point from which to measure the correct height for the bathroom furniture
Now, mark out the critical dimensions
Start with the base line
You’ll use this to mount the washstand and the high frame
In this case, it’s 235 mm from the floor
which is the height of the legs
That means you can align it with high cabinets with legs
The recommended height from the floor
to the top of a washbasin is around 885 mm
But put it where it feels right for you
If you’re installing a wall cabinet mark out the bottom line at 1,285 mm
Mark on the wall where you’re going to put your washbasin
Check that there’s enough space below for the pipes etc
Cabinets
The closed cabinets feature lightweight boards
and the wedge dowel
which reduce material consumption
Closed cabinets can be mounted with or without legs
Follow the assembly instructions
You’ll find the wedge dowel makes the cabinets really easy to assemble
All it takes is a click and a couple of screws
Use the base line to mark the cabinet mounting holes
A diamond-tipped drill bit helps avoid tile damage
If you haven’t got one
the next best thing is to put masking tape on the tile to prevent the drill from slipping
and use a regular masonry drill bit
Before you drill
make sure that there are no electrical wires
or water pipes behind the wall that could be damaged
Use screws and fixings that are suitable for the wall type
If you're not sure what to use, check with a professional
Once you’ve drilled the holes
fill them with a little silicone
This helps make the wall waterproof
We recommend sanitary silicone
Screw in the wall screws, leaving enough room to hang the cabinet
Now hang the cabinet on the screws
make sure it’s in the right position
then lock it in place using the keyhole washer
We use a coating technique on the open metal frames to prevent rusting
They also have a variation of the wedge dowel
By following the instructions you’ll find it easy be able to assemble them
As with other ENHET cabinets, all it takes is a simple click
When installing a wall cabinet, use the bottom line that you marked out earlier
Mark out a vertical line along the side of the washstand
hold the cabinet in alignment with the lines
and mark out the holes for the wall fixing
Fix the screws half way in so that you can adjust them
and align the cabinet with your other cabinets
The closed wall cabinets are as easy to assemble as the closed base cabinets
Again, you just click them together
Align the cabinet with the base line and with the other cabinets
and tighten the screws
Assemble the high cabinet according to the assembly instructions
It can be mounted with or without legs
Align the high cabinet with the top and side of the wall cabinet
Mark the holes for the wall fixing
Fix the screws half way in so that you can adjust the cabinet
and align it with other high cabinets
Washbasin, tap and water trap
Time to install the washbasin, tap and water trap
Use the assembly instructions as a guide
First turn the washbasin upside down
And install the water trap
Screw the parts together loosely
Next, install the tap
It comes with connection hoses
an installation tool, a water strainer and fittings
All our taps also come with ceramic disc cartridges
and water saving aerators
Mount the tap on the washbasin
Loosely tighten the two nuts with the installation tool provided
Later, you can adjust the tap to ensure it’s central
Time to fix the washbasin to the washstand
Apply silicone to the edges
Using tape when you apply the silicone
helps avoid smears of silicone on the washbasin and washstand
Next, place the washbasin on top of the washstand
Remember to remove the tape
as soon as you’ve aligned the washbasin with the washstand
This helps avoid excess silicone on the surface of your furniture
Now make sure the tap is central and fix it
Don't over-tighten the nuts
on the connection hoses as this can damage the rubber washer inside
Drawers, doors and mirror
Putting on the drawer fronts is simple
Click the drawer sides together and slide in the bottom piece
Then put the metal supports that come with the drawer
into the pre-drilled holes
Align the holes on the drawer with the ones on the front
and secure them with the plastic fitting
Slide the drawer into the cabinet
by aligning the back wheels of the runner with the front wheels of the sliders
Drawers can be aligned upwards and downwards
Use an Allen key to adjust them
Time to put on the doors
Put on the hinges that come with the cabinet
You can hang the doors to the left or to the right
You can adjust them in six different ways by using the screws on the hinges
The ENHET bathroom has a hanging mirror
Attach the fittings and hang the mirror on the rail
It’s easy!
Remember to attach all three fittings so that the mirror is secure
Now add the knobs and handles
Measure and mark where you’re going to put them
Drill the hole and attach them to the cabinet
For some handles a drilling pattern is helpful
Lighting and accessories
A bathroom needs to be well-lit
Here, we have added top lighting
For the top lighting use your awl according to the marks
lift the plastic fittings and fix the lighting to the cabinet
The cable will fit perfectly into the groove
Finally – add the accessories that go perfectly with ENHET
This will bring extra style and functionality to your bathroom!
You now know how to install your new ENHET bathroom
Simple! Just a few clicks and you’re done!
Make it safe!
Attach cabinets to a fixed structure
Use screws that are suitable for your wall
Follow our ENHET installation guide