Friends to all, a huge hello today made my own short selection of all sorts of devices and
secret opportunities for the workshop, what will happen, let's watch the video, everyone has a
pleasant viewing, let's go. everyone has come across such bags. either to tie or do
something, this will be the topic for our first homemade product, we take with you a bolt washer and a nut,
just like that, apply thermal glue to the block and glue it, let it cool, apply
thermal glue and glue our lighter.
we set fire to our combat weapons and heat them
take the package and go through we got a glued bag
friends I think everyone will face such a problem when you twist the
screw to the very edge of the board, then what does it do? right, it
bursts! to avoid this, we take the same self-tapping screw the same, we twist it a little and
scroll it in the opposite direction,
so we see nothing about doing a similar operation, we only take it to the very edge, we twist it a
little and in the opposite direction, we
twist it, now we twist it to the very edge and everything is fine he even burst without tightening up to the end
. I think the idea is useful, take note, this is of course provided if
you do not have a drill. like it! let's go further! friends as we can see a broken off screw to unscrew
it I do not know how. I will use such a tube this is a selfie camera that we
take and clamp it in our screwdriver and when tightened it pulls up and
will not scroll. now we take it and just screw it on and now our self-tapping screw has already seemed
good here, right away you will be in size under the dowel, I don’t have dowels,
you can quickly cut it, when I adjusted the dowel, I dipped glue into PVA, now we hammer,
take a saw and just saw off, then you can work as well. drove on.
By the way, I processed it a little with sandpaper and the connections are straight, I
just didn't get a picture. Now that the next can do
so to hide the screw to hook a little splinter podginaem and so take
sverlyshko Drill holes large drill bit zinkanul,
take a tablet that will tie take the screwdriver and fasten now
we need PVA glue the whole thing presses and tighten using the clamps
leave to dry and you can see that the connection is hidden, the hat is nowhere to be seen and it is not
visible that the tree was cut. I faced such a problem
when we have a twist and accidentally we do not find electrical tape at hand,
there are two quick ways that can be done, for the first method, the gun will come up to the term,
as a result, we have such a sealed twist. but the unity minus, of course, will melt when heated, but the
electrical tape will also warm up with us, it all depends
on how the wiring is done correctly. for the next method we need a burner,
but I think everyone has a burner. we take a plastic lid and heat it
in this way, we also get a sealed twist, it will certainly
be stronger than thermo-glue, but more dangerous because you can get burned and burn something.
have someone some way even how fast you can make prompt insulated
cable write in the comments! friends also make a lot of mistakes many motorists make,
and who works with wires I do these ordinary twists on soft wires,
that is, yes, we kind of twist everything, with electrical tape, but in fact it turns out that
we pulled it and everything untied! there are two good ways to do it!
one way in this way we just wind us up on each other
much, but this will answer the wire did not come off on the twist, the wire came off, that is, the
topic of workers to solder in general will be cool, just take two wiring about the same cleaned and
make a little bend on one ring and not over on the other, we also do a
similar loop, we also bend everything in the same way, then we take it in a circle, we turn it back a little
and we tighten it, we got a good knot, you can still twist it all on each side,
but this one will generally be a twist circle, it will only break, but again you see it
breaks not on the twist itself, which one you choose, it's up to you,
I just showed you also made me do the dog drilled the hole the sides all this
screwdriver take our improvised twist we put it all in the hole
clamped with pliers and start twisting it
turned out such an excellent twist right in five seconds
we didn't want to make lambs for such a bo lta twirl the neck of the bottle in this hadith somewhere,
we take a friend by pouring it in a vice between the boards and sort it out, we heat our blank
in general, so until it all turns out now, it will cool down a little and we will process it all
and then see the end result, in general, we have such a lamb but in a hurry,
yes, just like that, I did another one, everything is cool, we take on the arsenal of friends, we got
such a selection of ideas here, but of course the idea is new, all of this is on the Internet, I just
showed my performance to someone who liked it, put your finger on who didn't like it
, you know what can I do I also look forward to your comments but see you again bye bye