- [Voiceover] Let's say you have a circuit here
and you had a battery with a voltage v
and there were resistors one,
resistor two,
and resistor three up here,
and there was current flowing through here.
What if you wanted to experimentally measure
the voltage across some of these elements?
You'd have to use a voltmeter.
Voltmeter looks like this.
So a circle with a v in it
is the symbol we use for a voltmeter.
How do you use it?
You take that voltmeter, you bring it over to here.
I can't plug it in the circuit like that.
What I do is I take the leads of the voltmeter
and I just connect them
to either side of the circuit element
that I want to determine the voltage across.
So if I do this and I connect those leads right here,
this voltmeter will tell me the voltage across R three.
Or take the voltmeter,
put it over here,
and if I connect the leads
across R one in parallel,
notice I'm hooking up the voltmeter
in parallel.
Voltmeters you always hook up in parallel.
This now will tell me the voltage across R one
and if I wanted to make sure
my battery was functioning correctly,
I could take my voltmeter and I can
hook up the leads across the positive and negative
terminals of the battery
and see if the voltage across the battery
is what I think it is.
That's how you use a voltmeter:
always hooked up in parallel.
But if I wanted to measure the current,
I don't use a voltmeter, I use an ammeter.
And for an ammeter you do not hook up an ammeter
in parallel with the element you're trying to measure.
You will probably blow out the ammeter.
I've done it a few times.
It's embarrassing.
Don't hook up the ammeter in parallel,
tell you why in a minute.
But what you have to do is hook it up in series.
So if I wanted to know the current
going through R three,
I could just stick the ammeter right in here.
One lead would plug into one side of the ammeter,
the other lead would plug into the other side.
This current would have to
flow straight through the ammeter
and this is telling me how much current
goes through R three.
It doesn't matter what side I put it on,
the current going into R three
will equal the current going out.
So you can put it over here too,
but it's gotta be hooked up in series.
So you have to disconnect,
it's kind of a pain
to hook up an ammeter sometimes.
You have to disconnect something here,
then connect that connection to the one side of the ammeter,
connect to the other side of the ammeter.
For a voltmeter, you didn't have to do that.
For a voltmeter, just kept it out here
and just touch those leads
wherever you needed to touch them.
But for an ammeter,
you have to break the circuit to let this ammeter in.
But I can move it wherever I want.
I could put it down here,
that tells me the current in this strip.
Again, ammeters always hooked up in series
with the element that you're trying to measure.
So this ammeter position will let me measure
the current that's flowing through the battery.
But why is the voltmeter always hooked up in parallel
and the ammeter always hooked up in series?
We want the ammeter to be hooked up in series
because we want to measure the current
through a line in the circuit.
We want to measure the current
flowing through this resistor.
So if we want to measure the current
flowing through something,
we need to make sure that the current flows
through our ammeter
and that's how we get our reading.
Because of this,
people design ammeters with very little resistance.
An ammeter has very little resistance.
And the reason is,
if you took this ammeter and it had a big resistance
and you stuck it in here,
you'd be changing how much current flowed
through this part of the circuit.
We don't want to do that.
Whenever we measure something,
we don't want to disturb it.
So when I stick my ammeter in here,
I don't want to disturb how much current
was going through here.
I wanted to know how much current flows
without my ammeter being in there.
So when I put my ammeter in there,
it better have very little affect on this circuit.
That's why we make this ammeter
have a very small resistance.
And that's also why you can't
hook this ammeter up in parallel,
cause if you did, look at what would happen.
This is why it's bad.
If I took this ammeter
and I hooked it up right here,
and I hooked the other side up right here,
look what the current's gonna do.
I've got current flowing through here,
current comes this way, goes this way,
reaches this fork in the road
and it's got a choice.
It can go to the left
or flow up through here
and go through R three
or flow through my ammeter,
but my ammeter has very little resistance.
I mean small, maybe on the order of a milliohm.
So all of this current that's flowing through here,
all this current's gonna choose to go through my ammeter.
It's gonna just skip all those resistors, forget that.
it just goes through the ammeter.
If you've got a normal-sized voltage,
maybe nine volts, three volts,
hooked up to a milliohm,
you're gonna burn out your ammeter.
There's usually a fuse in here
because they know people are gonna hook it up wrong.
I've done that,
and you burn out a fuse,
you gotta go replace the fuse and it's a pain.
So don't hook up your ammeter in parallel.
What about voltmeters?
Why do we hook those up in parallel?
Well, a voltmeter is hooked up in parallel because
we want to know the voltage
across a circuit element,
so on either side.
Voltage, remember, is defined to be the difference
between electric potential at two points in space.
It makes no sense to ask what's the voltage
through a certain point in a circuit.
You can ask what current flows
through that point in the circuit.
But asking what the voltage is
at a particular point in a circuit makes no sense.
The only thing that would make sense
is asking what's the voltage
across two points in a circuit.
So I can ask what's the voltage between
this point and that point,
that makes sense,
or I can ask what's the voltage between
this point and that point, that makes sense.
But asking what's the voltage at a point
or through a point,
makes no sense.
That's what current is.
Current flows through a point,
voltage is across two points.
The difference in electric potential between two points.
That's why we hook up voltmeters in parallel
and because we hook up voltmeters in parallel,
voltmeters have to have a huge resistance.
Sometimes on the order of hundreds of thousands of ohms
or even millions of ohms.
So this can be big, big number of ohms.
And the reason is,
think about it,
again our key idea is that we don't want to disturb
the thing we're measuring.
I'm measuring the voltage across this resistor.
If I were to hook up a voltmeter
with very little resistance,
I just told you what would happen.
This current that's flowing out of the battery,
would all try to go through this voltmeter.
Not only would it try to mess up the voltmeter,
but that's current that's not flowing
through R three anymore,
and so I wouldn't get a correct reading
for the voltage through R three.
So we want to make sure our voltmeter has a big resistance
so that yes, technically a very, very small amount
of current, maybe a milliamp,
will flow through this voltmeter,
because it's gotta take a reading.
But, we want as small amount as possible,
because we want to keep this current flowing through R three
the same as it was before we were measuring it,
because I know v equals IR.
And if I can measure this voltage across here,
I want to make sure the current's the same,
or I won't be getting an accurate measurement
for the voltage.
You could ask what would happen
if we did hook the voltmeter in series instead of parallel.
Voltmeters have a huge resistance,
so if I stuck that here,
the voltmeter has a huge resistance,
you wouldn't break it,
it's just that,
think about what the current's gonna do.
Current comes out of this battery,
it's got a choice,
it can go up here through R three and the voltmeter
or through R one and R two.
I said the voltmeter has hundreds of thousands,
even millions of ohms,
so this current's just all gonna go this way.
Forget that.
It's gonna skip this entirely.
If you hook up a voltmeter in series instead of in parallel,
you just kill off any current through this portion
of the circuit that the voltmeter was hooked up in.
You probably won't break it,
so it's not as delicate as the ammeter,
but you still mess up your measurement
because it wasn't designed to be used that way.
So remember voltmeters are hooked up in paralled
to the circuit element that you
want to determine the voltage across.
But ammeters are connected in series
to the circuit element that you want to measure.
And if you're sitting there thinking,
"Pfft, I'm never gonna hook up my ammeter in parallel.
"How dumb do you think I am?"
Well, gotta be careful, cause most multimeters
are both voltmeters and ammeters,
depending on where you set the dial.
So if you're sitting there all day
measuring current with your ammeter setting.
Everything's going well.
And then you go to measure a voltage,
but you forget to switch the dial
to volt instead of amps,
you'll be hooking up an ammeter
in parallel erroneously.
That's what happened to me.
Don't let it happen to you.
Check the dial on your multimeter.
Make sure it's on the function
that you want it to be
so you don't burn out a fuse.