Hello everyone, today I show you how to completely disassemble iPhone X and replace back cover
To disassemble the iPhone X you need the following tools:
• Screwdriver set • Plastic mediator
• Suction cup for removing display • Tweezers and opening plastic tool
• Hairdryer In the description under this video, I left
links to the back housing and necessary tools and parts for replacement.
To replace the case of the iPhone X you need to completely disassembly smartphone.
After disassembling you will need to reassemble everything back and not get confused in various
screws, I recommend using a magnetic mat.
Before disassembly, turn off the iPhone and remove the sim card tray.
Unscrew the two screws near the charging port with a Pentalobe 0.8 mm screwdriver
Take any hair dryer and heat the surface of the screen for 1-2 minutes.
Set the suction cup at the bottom of the screen and pull the ring up.
Next, take a plastic mediator and begin to disconnect the display module from the iPhone.
The case of the iPhone 10 opening like a book.
Open the display to the right side.
Using a Tri-Wing 0.6mm screwdriver, unscrew 5 screws and remove the metal panel.
Under the metal panel, you will see cables.
The first is disconnecting the battery cable, and then disconnecting
the 3 display cables.
Unscrew 7 screws and remove the GSM antenna Unscrew the screw between the Taptic Engine
and the speaker.
Remove the metal panel and unplug the cable.
The speaker glued to the phone case.
If you want to save the adhesive tape, heat surface with the hairdryer.
Unscrew one screw and disconnect the cable.
Now you can remove the Taptic Engine.
Now you need to remove 4 adhesive tapes from under the battery.
Take tweezers and catch on the edge of the silicone tape.
Gently and slowly, pull the silicone tape away from the battery.
In the same way, remove the remaining 3 silicone tapes.
Unscrew the 2 screws and remove the metal bracket.
Disconnect all cables from the motherboard.
Unscrew the 3 screws from the motherboard.
Now you can remove the motherboard and main camera from the iPhone 10 case.
All remaining cables you can reinstall on the new iPhone back cover.
To do this, heat the surface with a hairdryer and reinstall it on a new back cover.
In the description under the video, you can find a link where
to buy a new back cover for iPhone X Lets begin to the reassembly.
Install the mainboard, connect the cables and fasten 3 screws.
Install the camera, then install the metal bracket and fasten
the two screws.
Install the Face ID module and connect 3 cables
to the motherboard.
The battery must be glue to the case, for this you can use a similar adhesive tape or
if you don’t have silicone tape, you can install the battery on double-sided tape.
Please note that double-sided tape is glue only to the metal part of the case.
Don't glue the battery to the wireless charging module.
Install the Taptic Engine into the smartphone case, fasten the screw and connect the cable.
Install the speaker into the case and connect the cable.
Set the metal panel and fasten screw.
Install the GSM antenna and fasten the 7 screws.
The iPhone X assembled and now you can connect the display module, test how the smartphone
works and begin to the final assembly with gluing the phone case.
To test the iPhone, you need to connect 3 display cables and after the battery cable.
Turn over the display, but do not close the case, just flip it.
Turn on the iPhone and check how the smartphone works.
If everything is working properly, let's begin to the final assembling.
Remove old glue from iPhone X case
Using medical alcohol, wipe the iPhone X case from the old adhesive tape.
If you want to restore the water resistance of your iPhone X, you need adhesive tape like
this.
Of course, you can assemble your iPhone X without this adhesive tape, but this makes
no sense because this adhesive tape costs only a couple of dollars.
In the description under the video, you find a link where to buy this adhesive tape.
Connect 3 display cables to the mainboard and only after connect the battery cable.
Install the metal panel and fasten
the screws.
Turn over the display and press it to the case.
Fasten the 2 screws near the charging port.
Install the tray with a sim card.
Now you can turn on your iPhone X and use it.