Hi. My name is Cody
I am with Northern Brewer homebrew supply and today Northern brewer's going to show
you how to build a keezer. So, what is a keezer?
It's basically a repurposed chest freezer for serving keg beer.
Building a keezer is a fairly easy process as long as you have a little bit of know-how
and the right tools and accessories before we get started I do want to say that
like most things in the home brewing there's more than one way to do this project and there
is no cookie-cutter answer we're just going to show you one way to get it done.
The whole thing begins with a chest freezer These you can find that most home appliance
stores or on ebay and craigslist and they come in all sorts of sizes.
There are three things to consider when choosing a chest freezer
First: how much space are you willing to dedicate to the keezer inside your house basement or
living room? Second: How much beer do you plan on serving?
2 kegs or 12 kegs? and third do you want to fit your co2 container
on the inside or will it be sitting outside of the freezer?
Purchase a chest freezer accordingly. Here's a quick look at what we're about to
do: Disconnect the freezer door hinges.
Remove the lid of the freezer. Build a collar to house are tapped faucets.
Assemble and connect a gas side and liquid side tubing.
Reattach the hinges and lid. Attach our faucet shanks and faucets.
Set a temperature control for our beer serving temperature and finallyhave a beer.
Ready? Let's do this! Once you have the chest freezer in your work
area we want to remove the hinges this is where first bit of advice comes in
handy have a partner There are several parts of the keys are building
process that our best handled with four hands if possible
This first part could be dangerous if you don't have some help
as you remove the top and bottom screws of the hinge the spring inside will
react swinging out and possibly injuring you. Use caution.
Have your building buddy hold the hinge in place as you remove the screw then
slowly ease the spring out. Repeat this process on the other hinge.
Set the screws aside as will be using them later.
Take a look at your hinges before purchasing the materials for your collar.
Depending on the hinge size, shape, and placement you may need to adjust the
size of the lumber you purchase. Next we are going to build the collar.
Think of the collar as a spacer into which we are going to drill holes for the beer
lines and tap faucets. We do this so we don't have to drill directly
into the freezer, it's cooling line and electrical components which could ruin your freezer and
potentially be dangerous. First, measure the dimensions of the top lip
of your chest freezer from edge to edge.
The freezer in our video measures 48 inches long by 27 inches
deep. we suggest using two-by-fours for the collar.
Measure the boards and cut them for the lengths of your freezer.
Remeber to take into consideration the build of your coller when blue printing your
design. The width of your lumber will affect the boards
required length. You could also have these boards cut for you
at a hardware or lumber store based on your freezer's measurements.
Before actually constructing the collar, set the pieces on top of the freezer and
make sure they fit up against one another with no large gaps are excess
wood hanging over the side of the freezer. You want the boards to be flush with the outside
perimeter of the cooler. Before we can construct the collar, we want
to draw the holes for the faucet taps.
This is easier to do while the boards are still separated.
Figure out which board will be your front facing tap handle board.
Next, decide where exactly you'd like your tap handles to be placed, front-and-center,
off to the side, your choice. You'll also want to decide how high up you
want them. We chose to place ours slightly lower to avoid
a lip at our freezer lid. With a spade bit, drill your holes leaving
at least three inches between each hole for proper spacing.
After the first hole is drilled, check to make sure your shanks fit through the
opening. Then, proceed with drilling the rest of the
tap faucet holes. Our keezer will not only house five co2 tap faucets on the front, but
one one stout faucet on the side. With your holes drilled, it's time to construct
the collar. For this step you'll need at least eight wood
screws. In our case, one and three quarter inches
long and inappropriate drill bit for priming the hole.
Have your building buddy hold the first two boards flush together.
Prime the screw holes with a drill bit, then insert the screws to fasten the two
boards together. In a perfect world you'll be able to do this
without the boards splitting. But, if it does form a small split relax,
don't worry we can fix that later. Repeat this process for all corners of the
collar into you have a sturdy rectangular frame that rests perfectly on top of the cooler.
Once you have the frame fit for the freezer, it's time to apply sealant and
let's set for a few days. Make sure to choose a sealant that will properly
adhere wood to plastic and functions that whichever temperature will be resting at over
the next few days.
This can be found at any major hardware store. Apply it generously to the top lip of the
open freezer. With your partner, carefully set the collar
on the sealant. Make sure it lines up perfectly with the outside
edges of the freezer. wipe away any excess sealant with a paper
towel. The sealant needs to set now for a few days.
Follow the directions on the packaging and resist the urge to go any faster.
We suggest weighing it down to help set. For this we set the lid back on top and put
a few kegs on top of that you can also use free weights bricks on top of a blanket or
any other heavy item you've got laying around.
We're gonna leave the freezer like this for two to three days to ensure proper seal.
While waiting for the collar to adhere properly, you can use this down time to assemble your
gas and liquid side tubing to ensure the ready to install the moment your
collar is ready. Let's begin with the gas side.
Here's a look at the tools and parts you will need
a co2 canister a dual gauge co2 regulator
1.4" barbed barb swivel nuts roughly four feet of 1/4" ID beverage tubing
oetiker clamps co2 distributor 6-way with 1/4" MFL shutoffs
Ball lock disconnects 1/4" MFL gas For those of you already kegging, these parts
should be fairly familiar. The only new tool we'll be adding is a gas
distributor for getting co2 from one canister to a multitude of kegs.
The first step is to connect your regulator to distributor.
Measure out how far away your CO2 canister will be from the distributor and cut that
length a 1/4" ID gas tubing. YOu'll want to first place an oetiker clamp
over the tubing, followed by your 1/4" swivel nut, then simply fasten the oetiker clamp
in the place.
Once this gas line is complete, you can screw one end into your regulator and the other
end into the gas side of your distributor. In order to properly use the oetiker clamps,
you'll need the otiker Clamper to tightly squeeze the clamp shut.
The good and bad thing about Oetiker Clamps is that once they're in place they don't come
off easily so be sure you're getting it right the first time.
Something you'll find when working with tubing is that it can be difficult to get the smaller
pieces inserted into the open end. Brute force can work but a much easier solution
is heating some water and soaking the ends of your tubing for a minute
or so. This will soften the tubing and allow greater
ease connecting the accessories. Next we'll want to prepare the gas lines going
from the distributor to your case. Measure out how far away from the distributor
your kegs will be. 3 to 4 feet is usually plenty and cut your
tubing accordingly Now we're going to attach the exact same pieces
as before either end Oetiker Clamp followed by a swivel nut.
Once this is complete, simply screw your gas side ball lock disconnect on one end and attach
the other end to distributor. Repeat this process for each keg and you're
ready to move on to the next step. Now we've got our gas side ready, let's look
at the liquid side. Here are the tools and parts we're dealing
with here: A ball lock disconnect
5 feet of 3/16" ID beverage line tubing connected with Oetiker 145 Clamps.
You'll also need the following: Tail Piece 1/4" stainless (SKU K214)
Beer Shank Wing Nut (SKU K087) Oetiker 145 Clamps (SKU K126)
Black Neoprene Beer Shank Washers (SKU K030) Beer Shank Stainless 4" (SKU K166)
Now let's put it all together. You'll want to make sure to use 3/16" inch
tubing for your liquid side. At five feet in length, this provides the
proper amount of resistance to serve foam free beer.
were you do use 1/4" tubing for example, that beer flows so rapidly that excessive foaming
becomes an issue. we're going to start by putting the Oetiker
Clamp over the tubing, followed by the liquid side ball lock and then using our Oetiker
Clamper to get a tight connection.
On the other hand a liquid side tubing, you'll first put the Oetiker clamp over the tubing,
followed by the wing nuts and finally the tail piece.
Again, tightly squeezing the clamp into place. You do not need to force the entire length
of the tail piece inside of the tubing. It's better to leave some room for the wing
nut unscrew properly. You'll need to repeat this procedure for each
liquid line you plan on creating, in our case six times.
At this point we have everything we need to finish our keezer.
Once the collar is sealed, we're ready to install all of our hardware.
First, let's carefully remove the weight from the lid.
You can use any wood putty or patch to fix gaps that formed while constructing the collar.
No harm. No foul. Installing the shank is as simple as unscrewing
the outside washer - placing the shake through the hole you drilled on day one
and hand tightening it in the place making sure that the faucet connector is on the outside.
Repeat for each shank. Installing the liquid tubing is just as easy.
Grab your neoprene beer shank washer and place it on the tail piece inside of the
wing nut. Then, simply screw the wing nut into place
on the and of your shank again repeating for each shank.
Voila! Your liquid lines are ready. There are two things to consider while attaching
your Co2 distributor. First: make sure it's in a place that can
easily reach all of your kegs. And, second: make sure it's out of the way
if you lid hinges Attaching the distributor is as simple as
gently securing it hand tight into the collar. There's no need for this to be completely
tight or flush, do what works for you. In our design, we chose to leave the Co2 canister
inside of our freezer. Note that if you go this route, the pressure
gauge on your canister will read closer to 650 or 700 psi due to the drop in
temperature in your freezer. This is completely normal and causes no problems for your design.
Another option if you have a smaller freezer and want to use that space for another keg
is to leave your Co2 canister on the outside of the freezer.
In this case you simply want to draw another hole through your collar and thread the tubing
from your canister through it to the distributor. Either way, make sure that your distributor
valves are set to the off position for now. Now it's time to reattach the hinges.
Place the lid on the collar and make sure that hinges lineup flush with where you plan
to attach them. This will vary from freezer to freezer and
our case were putting screws into both the collar and back into the freezer. This
is another time when it can be helpful to have a buddy.
Remember these springs can be strong, having a friend to help hold them in place can make
retention hinges much simpler and safer. Start by reinserting the screws you removed
from the body of the cooler on day one. If the hinges are properly aligned they should
be easy to do by hand. Next, using the appropriate drill bit, prime
the hole for the part of the hinges that will be connected to the
collar. Now, insert the wood screws to attach the
hinge to the collar. Open the lid and make sure everything lines
up perfectly before continuing. Once your hinges are connected and your lid
is secure, it's a good time to move your freezer into position before has the additional weight
of full kegs inside. Now is also a good time to attach an adjuster
temperature control unit. Plug your control unit into a nearby outlet
and plug your freezer into the control unit.
Then, place the probe inside of your freezer and set the temperature to your desired serving
temp, roughly 40º to 45º fahrenheit Attaching your faucets is as easy as can be.
Just bring the faucet to the shank and screw it into place, keeping the faucet vertically
aligned. One tool we recommend is the Faucet Wrench
(SKU K080). Specifically built for this process, it allows
you to get a tighter seal than just hand tightening would.
Repeat this step for each faucet. We finish our keezer with a fancy stout faucet
on the side. Again, the faucet wrench insures a tight seal.
The final touch is a nice tap handle for each faucet.
Hand tighten each handle using the spacer on the faucet to adjust the height as needed.
Here at Northern Brewer we offer a wide variety of handles from economy and stout handles
to chalk board and dry erase. Before putting your kegs inside the keezer,
make sure all connections along the collar are tight inside and out.
Now comes the hard part: choosing which beer you want on tap.
Place your kegs inside of your keezer and attach the gas and liquid ball locks.
Set your Co2 canister to serving pressure (from 6 to 12 psi)
Then open the gas valve on the distributor for that keg.
Do this for all the kegs you plan to serve. Before you put your beer on tap, it's a good
idea to run some cleaner through the lines. One good method is to fill a keg with beer
line cleaner or even just some PBW. Pressurize it. And pour through each line.
It's a good idea to clean your lines regularly. Good beer poured through moldy lines quickly
turns into a bad beer. After running clear through your lines it's
a good idea to rinse them with water. We suggest also from a pressurize keg before
you attach a keg of beer. One final option for your keezer is a drip
tray. This easy to install item comes in many sizes,
so choose the one that best suits your design. And, that's it.
With the keezer properly built and all the lines in place, it's
time to enjoy a homebrew. You deserve it!
Building a keezer at home is a great project I know I enjoy doing it myself.
You get cold beer on tap. It looks wonderful and you avoid the tangled
mess of lines in your freezer. Again, this is just one way to do it, not
the way to do it. For more information on parts and accessories
you can visit us at NorthernBrewer.com. You can also get in touch with other home
brewers and Keezer builders on our forum. A hand built keezer is just another way to
brew share and enjoy!