Hey guys, John here with realtruck.com.
Today I want to show you how to dress up your pickup truck for under $1,500.
Okay guys you can see here we have our fender flyers out of the box.
They come with front and rear sets here and everything you need to put them on the truck,
comes with all the rivets that you're going to attach on here, and also all of your rubber
trim that you want to put on this.
And then I usually just take the screws, and I'll start them by hand just to get him in
the right place so that way we can adjust this and get it up on the truck nice and tight.
Okay we've got our screws in, we've got our clips on, so there you go guys.
All right so we're ready to put this on and what we're going to do then is we're going
to take our clamp first and we're just going to put it over here, where it's going to go
on.
Once we get this slid up on to the exhaust pipe here, we'll just take our ratchet and
socket and we'll tighten this down to hold this on, so we don't have to worry about it
falling off.
There you go, quick, easy, cool upgrade to your truck and that's really how simple and
easy it is to install this Go Rhino Exhaust Tip.
The Spec-D projector headlights, they come with everything that we need to get them installed.
We know everything's working, so we're ready to put it back in the truck, and we're just
going to lift her back up in here.
We got our top clips back in, we've got our screws replaced.
So what we're going to do then is we're going to jump over and do the one on the other side.
It's going to install exactly like this one is.
We'll come back let you guys see what it looks like when it's all done.
So we've got everything ready to go here to put on our bed light in.
So what we want to do before we do that is take a rag with some purple alcohol or something
along that line that's going to clean this up and just wipe it down real good, peel back
a little bit of our strip and we're going to start attaching it in here in our truck
bed.
It can kind of because it is a rope type style.
You can pretty much do whatever you want with it, but we're going to put it in here nice
and straight.
So I'm just going to get it started right here, and the best thing to do is actually
if you want to keep it nice and straight is just to peel a little bit of that tape at
a time.
The backing on it and that will help you keep this in here without it getting all over.
All right guys, what we've done is we've gone ahead and ran our wires in through here to
the tail light.
Put the tail light back in and we'll show you guys how the light works.
The Recon LED running lights.
What we're going to do with this one is, we're going to center it right here on the doors
so that a way whenever you open the door, the white light comes on and shines down onto
this running board, to give you a little bit more of visibility for getting in and out
of the truck.
So once we have it where we want it, then we'll go ahead and get this front part stuck
up here, and then we'll just start peeling this tape out.
Access off-road LED light, we have our 4.3 inch round LED lights, we also have the mounting
brackets that go with them, so you can install them.
Let's get this under the truck.
Okay once we have our mounting brackets in place, then we can go ahead and attach our
light.
We are just going to slide her right down here into the bracket, put our long bolt through.
At this point we can make up our mind whether we want to use the harness, or if we just
want to go ahead and wire these up ourselves.
We're going to use the harness on ours which is, like I said sold separately and get these
all hooked up and show you guys how it works.
As you can see here we've got our shocks out of the box.
They come with everything you need to get these on your truck.
That's how easy it is to put it together, so let's get it on the truck now.
Just go ahead and put it right up on here.
The Plasmaglow Fire and Ice LED tailgate light bar.
So we've got our light bar all hooked up, we've got our wire ran, we've got it all tagged
up nice easy underneath the truck.
So the only thing left to do then is just go ahead and take our four-way connector,
and plug it into our trailer connector right here, and it's all ready to go.