Hello people, and welcome! I will show you in detail, all the powerful audio effects
that you can make with
If you find mistakes in pronunciation or narration, please leave us feedbacks.
Check the quick index in the video description here to find the effect you are
looking for.
First of all, if you don't know, you can add any effect to a channel going to the
Mixer window
to get future effects, if this is not present yet. Right-click on an
and go to
selected before this. Select such slot and, on the right, find the
You have eight slots inside. Each effect will occupy one of them. To add one,
go to the left arrow, and choose one effect in the list. Each effect is rendered
by a particular window that has a
this window you can change the properties of the effect. You can open it anytime
double-clicking on the filled row. On the right of such, you can make the effect
on/off through the green circle, and you can set how much the effect has to cover
the original channel through this knob. This is also called
Wet
Dry
effect itself. This knob can be found in the effect windows themselves.
Let's see the
Insert
you the spectrum of the channel played. The orange sides are the frequencies that are
more intense. The darker parts are frequencies not active, or very low in power.
At the bottom you have the range of audio frequencies, from 20Hz to 20kHz in
decades. The spectrum shown is the output if this window is put in the last filled
row in the
doesn't have all the effects added.
Go back to the
cuts just the highest frequencies. The
the band pass one cuts low and high frequencies. The
narrow band of frequencies that you choose through the knobs. For each filter you
can choose the
must be wide, and its
is a filter too. You can drag all seven points to set a personalized filter. Drag
up or down to set the
can change the bandwidth applied on each point going on
corner. Try also
Let's see now the
editing the signal, changing it or making it worse. It can be done with different
windows, like the
before and after. You can use
New in FL11 is the
any effect below. To edit the output, set the
TEMPO
The
hear like more channels together, all identical to the solo one before. This is
done with the
The
a special feeling. This is made through the
You can use the
A very important effect is the
kinds. The most traditional one is the simple
the original channel, and the same one but delayed. This is done by the
Delay Bank
You can set delay between stereo channels. Use the
Another kind of delay is the
reflection against walls, or any kind of material, in normal rooms or from metals.
Try the
samples, like kicks or snares.
There are many other features in FL11, especially editing samples properly, to
save them after. Add the window called
Play the channel solo, and record it through the
again to stop recording. You will obtain the channel waveform just recorded, that
you can replay using the
parts dragging your pointer. Then just right-click on such red area and go to
Double-click on a point to start with a new selection area, not to have problems.
Undo any mistaken action going on the button next to the lens. Mind that
undo just the latest action
to the first icon on the left and go to
properly an effect window, but a sample editor, that can be seen independent from
the channel itself linked. You can further work inside, making zooms, adding
other effects and equalizing. Similar to this is the
a little different because the waveform shown is used to make a
channel linked. The
Try it out!
Let's see two other effects that can be made with FL Studio 11. Open the
Beat window
But with this,
time graph
filled points you see. You can add new anchors right-clicking on the curve, and you
can personalize it better right-clicking on each point just added. The middle points
help you at editing such curve.
channel linked is played faster.
channel is played faster and faster, low frequencies become high ones.
channel to hear the effect. There are many options inside this window, just practice!
The second effect that can be done is the
in editing the channel waveform, stretching it, making it shorter or longer. This can
be done through the
can edit channels more into deep. Since Newtone can't import channels by recording,
you need to get the channel first
and
Newtone, in the
Now you can add warping. Simply drag the channel edges and edit the waveform.
Then just save the sample when you are satisfied. Mind not to have just the
demo version of this plugin,
Once it is saved, just import it in your opened pattern, and it will be played with
the warping edited and set.
The other windows you have in the list, such as the
used to improve the quality of the channel selected in the mixer.
Watch the next video of this show, to know how to use them.
Very well! I hope you enjoyed this video! Check the full playlist of these videos
to go on learning