A diving bell is a rigid chamber used to transport divers to depth in the ocean.
The most common types are the wet bell and the closed bell.
The wet bell is a cable-suspended chamber, open at the bottom like a moon pool structure,
that is lowered underwater to operate as a base or a means of transport for a small number
of divers.
The pressure of the water keeps the air trapped inside the bell.
They were the first type of diving chamber.
Unlike a submarine the diving bell is not designed to move under the control of its
occupants, nor to operate independently of its tether.
The closed bell is a sealed chamber, which may be used for mixed gas bounce diving and
for saturation diving.
This form of bell locks on and off the chamber where the divers live, by way of a closed
door sealing the divers in at pressure.
Once on the surface, the bell is mated with the chamber system and the space in between
is pressurized to enable the divers to make a seal and transfer through to the chamber
which is at the same pressure.
In saturation diving the bell is merely the ride to and from the job, and the chamber
is the living quarters.
If the dive is relatively short, decompression can be done in the bell in exactly the same
way it would be done in the chamber.
History
The diving bell is one of the earliest types of equipment for underwater work and exploration.
Its use was first described by Aristotle in the 4th century BC: "...they enable the divers
to respire equally well by letting down a cauldron, for this does not fill with water,
but retains the air, for it is forced straight down into the water."
According to Roger Bacon, Alexander the Great explored the Mediterranean on the authority
of Ethicus the astronomer.
In 1535, Guglielmo de Lorena created and used what is considered to be the first modern
diving bell.
In 1616, Franz Kessler built an improved diving bell.
In 1658, Albrecht von Treileben was permitted to salvage the warship Vasa, which sank in
Stockholm harbor on its maiden voyage in 1628.
Between 1663-1665 von Treileben's divers were successful in raising most of the cannon,
working from a diving bell.
In 1687, Sir William Phipps used an inverted container to recover £200,000-worth of treasure
from a Spanish ship sunk off the coast of San Domingo.
In 1689, Denis Papin suggested that the pressure and fresh air inside a diving bell could be
maintained by a force pump or bellows.
Engineer John Smeaton utilized this design in 1789.
The earliest applications were probably for commercial sponge fishing.
In 1691, Dr. Edmond Halley completed plans for a diving bell capable of remaining submerged
for extended periods of time, and fitted with a window for the purpose of undersea exploration.
In Halley's diving bell, atmosphere is replenished by sending weighted barrels of air down from
the surface.
In 1775, Charles Spalding, an Edinburgh confectioner, improved on Dr. Halley's design by adding
a system of balance-weights to ease the raising and lowering of the bell, along with a series
of ropes for signaling the surface crew.
Spalding and his nephew, Ebenezer Watson, later suffocated off the coast of Dublin in
1783 doing salvage work in a diving bell of Spalding's design.
Salvador Dalí once showed up to give a lecture in a diving bell, and insisted on speaking
from inside it.
Mechanics
Diving bells are used as underwater search vessels and by working divers doing underwater
work and salvage.
The bell is lowered into the water by cables from a crane attached to a ship or dock.
The bell is ballasted so as to remain upright in the water and to be negatively buoyant
so that it sinks even when full of air.
Hoses, fed by pumps on the surface, provide compressed breathing gas to the bell, serving
two functions: Fresh gas is available for breathing by the
occupants, and excess gas leaks out under the lip of the wet bell, where it bubbles
naturally to the surface.
As a wet bell is lowered, increasing pressure from the water compresses the gas in the bell.
If the gas pressure inside the bell were not raised by adding gas to compensate for the
outside water pressure, the bell would partially fill with water as the gas was compressed.
Adding pressurized gas ensures that the air space within the bell remains at constant
volume as the bell descends in the water.
A similar principle to that of the wet bell is used in the diving helmet of standard diving
dress, where compressed air is provided to a helmet carried on the diver's shoulders.
Additional weights are carried on the waist and feet to prevent overturning.
The modern equivalent of this diving equipment is used in surface supplied diving.
A wet sub may also provide a dry viewing chamber for the operator's head, acting as would a
diving helmet.
The physics of the diving bell applies also to an underwater habitat equipped with a moon
pool, which is like a diving bell enlarged to the size of a room or two, and with the
water–air interface at the bottom confined to a section rather than forming the entire
bottom of the structure.
Structure of a typical wet bell
A wet bell is a platform for lowering and lifting divers to and from the underwater
workplace, which has an air filled space, open at the bottom where the divers can stand
or sit with their heads out of the water.
The air space is at ambient pressure at all times, so there are no great pressure differences,
and the greatest structural loads are usually self weight and the buoyancy of the air space.
A fairly heavy ballast is often required to counteract the buoyancy of the airspace, and
this is usually set low at the bottom of the bell, which helps with stability.
The base of the bell is usually a grating or deck which the divers can stand on, and
folding seats may be fitted for the divers' comfort during ascent, as in-water decompression
may be long.
Other equipment that is carried on the bell include cylinders with the emergency gas supply,
and racks or boxes for tools and equipment to be used on the job.
Type 1 wet bell The type 1 wet bell does not have an umbilical
supplying the bell.
Umbilicals supply the divers directly from the surface, similar to a diving stage.
Divers deploying from a type 1 bell will exit on the opposite side to where the umbilicals
enter the bell so that the umbilicals pass through the bell and the divers can find their
way back to the bell at all times by following the umbilical.
Bailout from a type 1 bell is done by exiting the bell on the side that the umbilicals enter
the bell so they no longer pass through the bell, leaving the divers free to surface.
Type 2 wet bell A gas panel inside the bell is supplied by
the bell umbilical and the emergency gas cylinders, and supplies the divers' umbilicals and sometimes
BIBS sets.
There will be racks to hang the divers' umbilicals, which for this application must not be buoyant.
Operation of a wet bell The bell with divers on board is deployed
from the working platform by a crane, davit or other mechanism with a man-rated winch.
The bell is lowered into the water and to the working depth at a rate recommended by
the decompression schedule, and which allows the divers to equalize comfortably.
Wet bells with an air space will have the air space topped up as the bell descends and
the air is compressed by increasing hydrostatic pressure.
The air will also be refreshed as required to keep the carbon dioxide level acceptable
to the occupants.
The oxygen content is also replenished, but this is not the limiting factor, as the oxygen
partial pressure will be higher than in surface air due to the depth.
When the bell is raised, the pressure will drop and excess air due to expansion will
automatically spill under the edges.
If the divers are breathing from the bell airspace at the time, it may need to be vented
with additional air to maintain a low carbon dioxide level.
The decrease in pressure is proportional to the depth as the airspace is at ambient pressure,
and the ascent must be conducted according to the planned decompression schedule appropriate
to the depth and duration of the diving operation.
Structure of a typical closed bell A closed or dry bell is basically a pressure
vessel for human occupation which is lowered into the sea to the workplace, equalised in
pressure to the environment, and opened to allow the divers in and out.
These functional requirements dictate the structure and arrangement.
The internal pressure requires a strong structure, and a sphere or spherical ended cylinder is
most efficient for this purpose.
When the bell is underwater, it must be possible for the occupants to get in or out without
flooding the entire interior.
This requires a pressure hatch at the bottom.
The requirement that the bell retains its internal pressure when the external pressure
is lowered dictates that the hatch opens inward, so that internal pressure will hold it closed.
Locking onto a decompression chamber at the surface is possible either from the bottom
or the side.
Using the bell bottom hatch for this purpose has the advantage of only needing one hatch,
and the disadvantage of having to lift the bell up and place it over a vertical entry
to the chamber.
The bell bottom hatch must be large enough for a large diver fully kitted with appropriate
bailout cylinders, to get in and out without undue difficulty, and it can not be closed
while the diver is outside as the umbilical is tended through the hatch by the bellman.
It must also be possible for the bellman to lift the working diver in through the hatch
if he is unconscious, and close the hatch after him, so that the bell can be raised
and pressurised for the ascent.
The internal space must be large enough for a fully kitted diver and bellman to sit, and
for their umbilicals to be stowed neatly on racks, and the hatch to be opened inwards
while they are inside.
Anything bigger will make the bell heavier than it really needs to be, so all equipment
that does not need to be inside is mounted outside.
This includes a framework to support the ancillary equipment and protect the bell from impact
and snagging on obstacles,and the emergency gas supply, which is usually racked around
the framework and connected via manifolds to the internal gas panel.
The bell umbilical is connected to the bell via through hull fittings, which must withstand
all operating pressures without leaking.
The internal gas panel connects to the hull penetrations and the diver's umbilicals.
The umbilicals will carry main breathing gas supply, a communications cable, a pneumofathometer
hose, hot water supply for suit heating, power for helmet mounted lights, and possibly gas
reclaim hose and video cable.
The bell umbilical will usually also carry a power cable for internal and external bell
lighting.
Hydraulic power lines for tools do not have to pass into the interior of the bell as they
will never be used there, and tools can also be stored outside.
There may be an emergency through-water communications system with a battery power supply.
The bell may also have viewports and a medical lock.
Deployment of a modern diving bell
Diving bells are deployed over the side of the vessel or platform using a gantry or A-frame
from which the clump weight and the bell are suspended.
On dive support vessels with in-built saturation systems the bell is deployed through a moon
pool.
Deployment usually starts by lowering the clump weight, which is a large ballast weight
suspended from a cable which runs down one side from the gantry, through a set of sheaves
on the weight, and up the other side back to the gantry, where it is fastened.
The weight hangs freely between the two parts of the cable, and due to its weight, hangs
horizontally and keeps the cable under tension.
The bell hangs between the parts of the cable, and has a fairlead on each side which slides
along the cable as it is lowered or lifted.
Deployment of the bell is by a cable attached to the top.
As the bell is lowered, the fairleads prevent it from rotating on the deployment cable,
which would put twist into the umbilical and risk loops or snagging.
The clump weight cables therefore act as guidelines or rails along which the bell is lowered to
the workplace, and raised back to the platform.
If the lifting winch or cable fails, and the bell ballast is released, a positively buoyant
bell can float up and the cables will guide it to the surface to a position where it can
be recovered relatively easily.
The clump weight cable can also be used as an emergency recovery system, in which case
both bell and weight are lifted together.
The bell umbilical is separate from the divers' umbilicals, which are connected on the inside
of the bell.
The bell umbilical is deployed from a large drum or umbilical basket and care is taken
to keep the tension in the umbilical low but sufficient to remain near vertical in use
and to roll up neatly during recovery.
Bell cursor A bell cursor is a device used to guide and
control the motion of the bell through the air and the splash zone near the surface,
where waves can move the bell significantly.
It can either be a passive system which relies on additional ballast weight or an active
system which uses a controlled drive system to provide vertical motion.
The cursor has a cradle which locks onto the bell and which moves vertically on rails to
constrain lateral movement.
The bell is released and locked onto the cursor in the relatively still water below the splash
zone.
Use with hyperbaric chambers Commercial diving operators now generally
use a closed bell in conjunction with a surface hyperbaric chamber, These have safety and
ergonomic advantages and allow decompression to be carried out after the bell has been
raised to the surface and back on board the diving support vessel.
They are used especially in saturation diving and undersea rescue operations.
The diving bell would be connected via the mating flange of an airlock to the deck decompression
chamber or saturation system for transfer under pressure of the occupants.
Rescue bell
Diving bells have been used for submarine rescue.
The closed dry bell is designed to seal against the deck of the submarine above an escape
hatch.
Water in the space between the bell and the submarine is pumped out and the hatches can
be opened to allow occupants to leave the submarine and enter the bell.
The hatches are then closed, the bell skirt flooded to release it from the submarine,
and the bell with its load of survivors is hoisted back to the surface, where the survivors
exit and the bell may return for the next group.
The internal pressure in the bell is usually kept at atmospheric pressure to minimise run
time by eliminating the need for decompression, so the seal between the bell skirt and the
submarine deck is critical to the safety of the operation.
This seal is provided by using a flexible sealing material, usually a type of rubber,
which is pressed firmly against the smooth hatch surround by the pressure differential
when the skirt is pumped out.
Underwater habitats
As noted above, further extension of the wet bell concept is the moon-pool-equipped underwater
habitat, where divers may spend long periods in dry comfort while acclimated to the increased
pressure experienced underwater.
By not needing to return to the surface they can reduce the necessity for decompression,
required to avoid problems with nitrogen bubbles releasing from the bloodstream.
Such problems can occur at pressures greater than 1.6 standard atmospheres, corresponding
to a depth of 6 metres of water.
In nature The diving bell spider, Argyroneta aquatica,
is a spider which lives entirely under water, even though it could survive on land.
Since the spider must breathe air, it constructs from silk a diving bell which it attaches
to an underwater plant.
The spider collects air in a thin layer around its body, trapped by dense hairs on its abdomen
and legs.
It transports this air to its diving bell to replenish the air supply in the bell.
This allows the spider to remain in the bell for long periods, where it waits for its prey.
See also
Bathysphere Benthoscope
Diving chamber Moon pool
Timeline of underwater technology References
External links Diving Bell: Kenyon College Department of
Physics Historical Diving Society: The History of
the Diving Bell Historic diving bells
Modern diving bells close call rapid depressurisation