Hello everyone, today I show you how to disassemble iPhone XR and replace back cover
To disassemble the iPhone XR you need the following tools:
• Screwdriver set • Tweezers
• Opening plastic tool • Plastic mediator
• Suction cup for removing display • Hairdryer
In the description of this video, I left links to the necessary tools and parts for replacement.
Before completely disassembling the iPhone XR, I recommend using a magnetic pad; this
will help not to get confused when reassembling your iPhone, because screws of different types
and sizes used in this model.
I left a link to this magnetic pad in the description.
Before disassembling, turn off the iPhone and remove the sim card tray.
Unscrew two screws near the lightning port.
Using a hairdryer, heat the display surface for 1-2 minutes.
In this way, the glue heat between the iPhone case and the display, so it will be easier
to open the case.
Apply the suction cup to the bottom edge of the display and pull up on the ring.
Next, push the plastic mediator between the display and iPhone case.
If you cannot do this with a plastic mediator, take any thin plastic card and insert it between
the case and the display, then it will be easier to pry with a mediator.
Now, evenly and slowly, open the display around the perimeter of iPhone.
The iPhone case opens like a book; the display opens to the right side.
Using a Tri-Wing screwdriver, unscrew the 3 screws and remove the metal panel.
Now you can disconnect the battery cable from the mainboard.
Next, unscrew the 2 screws and remove the second metal panel.
Unscrew another 3 screws with a Tri-Wing screwdriver and two screws with a PH00 screwdriver.
Disconnect 3 cables of the display from the mainboard.
Unscrew 2 screws and remove metal panel.
Disconnect the camera cable from the mainboard, after pry up the camera module and remove
it from the iPhone XR case.
Unscrew 7 screws.
Disconnect the cable.
Disconnect the cable, which is located between the speaker and Taptic Engine.
Now you can remove the Taptic Engine from the iPhone XR case.
Now the speaker can be remove.
Note that the speaker glued to the bottom of the case.
To keep the factory adhesive tape, use a hairdryer to heat the place where the speaker glued.
Slowly pull one adhesive tape away from the battery.
In the same order repeat with the other three adhesive tapes.
Disconnect all cables.
Now you can remove the logic board from the iPhone XR case.
Using hairdryer, heat the backside of the iPhone case where locate cables of Face ID.
Next, gently separate the cable from the iPhone case.
In the description of this video, I left a link where you can buy a new back cover for
iPhone XR
Install the logic board into the case and check that all cables must be above the logic
board.
Fasten 5 screws to the logic board.
Connect the cable.
Install the sim card reader and connect the cable to the logic board, then fasten 2 screws.
Install the rear camera in to the iPhone case and install metal panel.
Fasten 2 screws.
Install the Face ID module in the iPhone case.
Connect 3 cables from the Face ID module to the logic board.
The
battery should be glue to the metal surface of the iPhone case.
Apply the adhesive tape and install the battery in housing of iPhone.
Install the speaker to the case.
Fasten 2 screws.
Install the metal part and fasten the screw.
Install the Taptic Engine and connect the cable.
Fasten 2 screws to the Taptic Engine.
Between the Taptic Engine and the speaker install the metal panel and fasten 2 screws.
Connect the antenna cable.
Fasten 7 screws.
Remove
the old adhesive tape from the iPhone case.
After, using medicine alcohol wipe the surface of iPhone case and display module.
Take a new adhesive tape and apply on the case.
With this tape, you keep the iPhone waterproof.
I left a link where you can buy this adhesive tape in the description.
Connect 3 display cables to the mainboard and only after that connect the battery cable.
Next, install all panels and fasten screws.
Now turn over the display and press the display to the case.
Fasten 2 screws near the lightning port.
Installing a sim card and now you can turn on the iPhone XR.
Good luck.