With TROBA-LEVEL, you can quickly and easily install self-supporting
tile pavers in exterior applications. The small number of components can be combined
in various configurations to allow for the flush installation of adjacent tile pavers and produce
level surfaces over sloped substrates. Open joints allow water to quickly drain
through the assembly and eliminate risk of freeze/thaw damage. The elevated assembly
also allows for quick and easy access to the waterproofing or drainage systems below.
The system can accommodate different paver thicknesses while maintaining flush transitions
across the surface of the assembly. Graphic/Title: Schluter®-TROBA-LEVEL
System Components The system components can be
classified into 3 categories: • Pedestals
• Height Extensions • And Accessories•
Let’s take a look at how the TROBA-LEVEL system works.
The Schluter®-TROBA-LEVEL System and all other installation materials must be installed in
accordance with Schluter®-Systems written installation requirements,
all applicable building codes and tile manufacturer’s installation instructions.
All substrates must be structurally sound and capable of supporting the anticipated loads.
The TROBA-LEVEL system can compensate for a substrate slope
of up to a 5% or 9/16” per foot. Start the paver installation at
the highest point of the substrate. For installations at edges or in corners,
TROBA-LEVEL-PL 10 paver supports can be cut into halves and quarters. Score the paver support with
a utility knife and bend to snap in half. Use a level to determine the number of
TROBA-LEVEL-AP 1 levelling shims required to bring the paver to the desired height.
The maximum number of shims that can be stacked is 10.
TROBA-LEVEL-PL 10 paver supports positioned away from the perimeter can be stacked with a 90°
offset if needed to obtain the desired height. When stacking halves of TROBA-LEVEL PL 10 at the
perimeter, first determine how they fit together prior to cutting.
Pay close attention to the 90°offset of each consecutive paver support to ensure
that a spacer tab remains between the paver tile and the perimeter structure or wall.
Again, use a level to determine the number of shims required to bring the
paver to the desired height. The minimum tile paver width is
3-3/8" when using TROBA LEVEL PL 10. For an assembly height of 2" or greater,
TROBA-LEVEL-PLA 30 extensions can be used between two TROBA-LEVEL-PL 10 paver supports.
For assembly heights greater than 2-3/8” (two and three eighths of an inch), TROBA-LEVEL-PLV
60 adjustable paver supports can be used. For installations at edges or in corners,
cut the TROBA-LEVEL-PLV 60 base plate at one of the pre-marked lines on the
underside and fold the corresponding wall spacer to the upright position.
This will allow the support to be positioned closer to the wall.
Remove any unnecessary joint spacer tabs by tapping sideways with a hammer.
Use the levelling shims as required. For assembly heights of 5-1/8" – 15",
TROBA-LEVEL-PLA 70 extensions can be inserted within the TROBA-LEVEL-PLV 60.
Completely screw the extensions into the TROBA-LEVEL-PLV 60 base plate….
…or into each other when multiple TROBA-LEVEL-PLA 70 extensions are required.
For additional protection of a waterproofing layer, such as a roofing membrane,
TROBA-LEVEL-PLS 6 protective pads can be installed under the base plates
of TROBA-LEVEL-PLV 60, TROBA-LEVEL-PL10 or TROBA-LEVEL-LV 3 paver supports.
For PVC membranes, the aluminum side of the pad is installed face-down. The four
perforated tabs can be lifted over the edge of the pedestal to maintain the position on the pad.
TROBA-LEVEL-PL 10 paver supports must be placed in the center of the pads when used
or used in combination with TROBA-LEVEL-LV3..
The TROBA-LEVEL System is the perfect solution to transform your exterior
living space into the balcony, patio, or rooftop terrace of your dreams!