hi everybody
today I perform UBIQUITI installation in Access Point mode
UBIQUITI has 2 connection ports
This is the PoE
Also includes 2 ports: PoE and LAN
Use 1 LAN cable connecting between PoE port and UBIQUITI
Plug one end of the LAN cable into the Main port
The other end is plugged into the PoE port
Use another LAN cable connect between the LAN port and the computer
You review the plug-in model as above
To make it easier to visualize in the previous step, look at the image above
This is the power with PoE port and LAN port
PoE port connected to UBIQUITI
LAN port connects to computer to perform installation
You watch it again
You move through the installation steps as follows
consists of 3 steps
Step 1: Login
Step 2: Set Access Point mode (AP)
Step 3: Turn off the airMAX function
You first set a static ip address for the computer
Ethernet, Network and Sharing Center
Ethernet
Properties
Internet Protocol Version 4 (TCP / IPv4)
You set the ip address as shown in the picture
192.168.1.100
255.255.255.0
Default Gateway
192.168.1.20
192.168.1.20 is the IP address of UBIQUITI
OK
OK, Close
After installing the static ip address for the computer
move on to login UBIQUITI NanoStation
Open any web browser
Chorme
on the address line enter 192.168.1.20
Advanced
Proceed to 192.168.1.20 (unsafe)
The login screen appears
as you see the login information as above
UBIQUITI's ip address
This is the login username and password
Both the username and the login password are: ubnt
User Name: ubnt
Password: ubnt
Country: United States
United States
Minimize the screen a bit
Check: I agree to ....
Check
Login
Wait a minute
OK, login successfully
switch to step 2: set up Access Point mode
Access Point
Return to the installation page and do the following
Wireless
Switch to Access Point mode
Access Point
SSID
Next is the wireless network name and wireless password
Set the wireless network name in the SSID box
example : NETVN
Wireless Network Name: NETVN
SSID
Wireless Security
You set the wifi password here
Security: WPA2- AES
WPA2 -AES
PSK
Set wireless password in " WPA Preshared Key" box
for example 123456789
Click "Change" to install
UBIQUITI will request to change the new login password
Change login password, not wifi password
The default login password is ubnt
The username and password are both ubnt
For example, I change the password to " admin "
ubnt
New password: admin
Verify new password: admin
admin
OK
Change
changed the successful login password to: admin
move on to step 3
Remove the airMAX feature
You switch to Tab settings
icon of UBIQUITI
UBIQUITI
You notice this place
Disable
uncheck
then press "Change"
unchecked
Click "Apply" to save the settings
Apply
waiting for the device installation life
After completing 3 installation steps
I switched to connecting UBIQUITI to the Internet
I removed the network cable connected to the computer
instead, the LAN port will be connected to the Internet
as shown above
The PoE port is attached to the Main port of UBIQUITI
You connect as shown
after the gas connects the LAN cable to the Internet
Wait a while for UBIQUITI to save the settings
You try connecting to UBIQUITI
WIFI
You will see the wifi network name just installed in the previous step
NETVN
Connect
Enter the correct password in the previous step
123456789
next
Successful wifi connection
So you have successfully installed UBIQUITI NanoStation
Youtube
Internet
netvn
Internet access available
You review the necessary information as above
UBIQUITI's ip address
The default username and password are ubnt
Step 2 is the Access Point mode setting
Step 3 is to disable the airMAX mode
Remember to take these 3 steps
Thank you for watching the video
If you find it interesting, click Like and subscribe my Youtube channel
If you have comments please comment below the video
Thank you