Required tools: Wire brush WD-40 spray Brake cleaner
All-purpose cleaning spray Copper grease Drive socket # 12 Drive socket # 13
Drive socket # 17 Drive socket # 32 Wheel impact socket #17 Ratchet wrench
Torque wrench Tap wrench Hammer
Rubber mallet Crow bar Wheel chock
1. Raise the rear of the car and secure on supports.
2. Unscrew the wheel bolts. Use wheel impact socket #17..
AUTODOC recommends: To avoid injury, hold up the wheel when unscrewing the bolts.
3. Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
4. Unscrew the brake caliper fastening. Use a drive socket #13. Use a ratchet wrench.
5. Remove the brake caliper. Use a crowbar.
AUTODOC recommends: Tie the caliper to the suspension or to the body with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.
Make sure that the brake caliper is not hanging on the brake hose.
Don't press the brake pedal after the brake caliper has been removed.
As a result, the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
6. Remove the brake pads.
7. Clean the brake caliper bracket fasteners. Use a wire brush. Use WD-40 spray.
8. Unscrew the caliper bracket fastening. Use a drive socket #17. Use a tap wrench.
9. Remove the caliper bracket.
10. Clean the brake disc fasteners. Use a wire brush. Use WD-40 spray.
11. Unscrew the brake disc fastening Use a drive socket #12. Use a ratchet wrench.
12. Remove the brake disc. Use a rubber mallet.
13. Remove the hub bearing protection cap. Use a crowbar. Use a hammer.
AUTODOC recommends: Some cars are not equipped with wheel hub caps.
14. Unscrew the wheel hub axle nut. Use a drive socket #32. Use a tap wrench.
15. Remove the hub and the bearing together, since they are a sealed unit.
16. Clean the hub bearing mounting seat. Use all-purpose cleaning spray.
17. Install the new wheel hub with a bearing.
18. Tighten the hub. Use a drive socket #32. Use a torque wrench. Tighten it to 95 Nm torque.
AUTODOC recommends: The wheel bearing unit must not tilt on the axle pin.
19. Install the hub bearing protection cap. Use a rubber mallet.
20. Treat the hub where it contacts the brake disk. Use copper grease.
21. Install the brake disc.
22. Tighten the brake disc fastening. Use a drive socket #12. Use a torque wrench. Tighten it to 10 Nm torque.
23. Clean the brake caliper bracket from dirt and dust. Use a wire brush. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
24. Install the brake caliper bracket.
25. Tighten the brake caliper bracket. Use a drive socket #17.
Use a torque wrench. Tighten it to 85 Nm torque.
26. Install the brake pads.
27. Install the brake caliper and fix it. Use a drive socket #13.
Use a torque wrench. Tighten it to 35 Nm torque.
28. Clean the brake disk surface. Use a wire brush.
29. Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
30. Clean the brake disk surface. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
31. Screw in the wheel bolts. Use wheel impact socket #17.
AUTODOC recommends: To avoid injury, hold up the wheel when screwing in the fastening bolts.
32. Lower the car and working in a cross order, tighten the wheel bolts.
Use a torque wrench. Tighten it to 110 Nm torque.