your Healthcare Professional has recommended the Mirage Quattro Full Face
mask from ResMed the Mirage Quattro offers effective treatment even if you
breathe through your mouth and being the fourth generation mask of its kind the
Mirage Quattro incorporates trusted features as well as new design to give
you a better good night's sleep
here's what's new about the Mirage Quattro
it's new forehead support comes with 24 positions offering a tailored fit to a
wider range of people it's improved cushion technology provides a better
seal and added comfort with fewer parts your mask is unobtrusive and easier to
handle assemble and disassemble
and its new built-in vent design means you're Mirage Quattro is quieter than
ever before which means a more comfortable sleep for you and your partner
The Mirage Quattro Full Face mask is designed for quick and easy fitting
simply follow these instructions
firstly make sure you're familiar with all of its parts
before you go to bed wash your face thoroughly we also recommend you do not
apply moisturizer for your Mirage Quattro will touch your face ingredients
in some skincare products may react with the mask cushion and reduce the
effectiveness of the seal now you're ready to put on your Mirage Quattro mask
make sure the forehead support is fully extended
but be careful not to overextend the pointers on the dial should be in the
vertical position disconnect one of the lower headgear clips from the mask frame
now put on the mask like this
placing the cushion over your face then pulling the headgear over your head
not like this as dragging creases the cushion and makes it difficult to get a good seal
then reconnect the free clip as a guide the upper straps should pass across your
forehead and the lower straps below your ears the straps should feel comfortable
to adjust unfasten the velcro on the upper straps pull evenly is required and
then refasten do the same with the lower straps
now adjust the forehead support turn the dial until you reach a position that
gives you the best steel and comfort or the position recommended by your
healthcare professional when the mask is in place the pads on the forehead
support should lightly touch your forehead and the mask should not be
touching your eyes now connect the main air tubing to the swivel on your mask
and switch on the flow generator
now lie down and roll your head from side to side to check you have a good
seal make sure there are no gaps or air leaks around the eyes and mouth if you
are unable to get a good seal try readjusting the dial or the headgear
straps but be careful not to over tighten your Mirage Quattro should fit
securely but not tightly
if you need to get up during the night
there's no need to remove your mask simply pull off the swivel and get up
when you come back simply reattach and continue your sleep
at the end of your sleep detach the tubing
switch off your flow generator and take off the mask by disconnecting one of the
lower headgear clips then lifting it up over your head
now it's your term pause the video here while you practice fitting adjusting and
removing your Mirage Quattro
to clean your Mirage Quattro Full Face mask thoroughly you will need to
disassemble it
here's a tip before you begin
note the position on the dial for when it's time to reassemble now begin
disassembling the mask by detaching the swivel you'll then need to detach the
elbow assembly from the mask frame pivot the elbow away from the mask like this
rather than try to pull it off like this
next it's time to remove the headgear you'll notice the side slots on the
forehead support these allow you to remove the upper straps without
unfastening the velcro and losing your settings the clips on the lower headgear
also mean you can detach them without losing your settings
this makes it easier to fit your mask the next time you use it next using the
protruding edge remove the valve clip from the elbow
now peel away part of the valve and slide the tab out of the valve clip like
this
be careful not to pull on the membrane the valve is very important to your
safety
it allows you to breathe fresh air if the air flow from your flow generator is
impeded for any reason now disassemble the forehead support by turning the dial
anti clockwise until you feel you cannot unscrew any further then give it one
more turn and remove the dial completely now squeeze the pole in the middle and
gently pull it out of the grooves then remove the pads from the forehead
support
next you need to remove the cushion clip and cushion from the mask frame squeeze
the colored tabs and push the top of the cushion out of the frame now slowly but
firmly pull away the rest of the cushion like this peel away the cushion to remove the clip
here's a tip always place the cushion with the membrane facing up to preserve it
lastly remove the port's cap
now it's your turn
pause the video here while you practice disassembling your Mirage Quattro
you're now ready to clean your mask fill your sink with warm water and mild
liquid soap or detergent follow the manufacturers directions for quantity
avoid using bleach or alcohol based products aromatic or scented oils
products that smell strongly of citrus
immerse each mask part in the soapy water gently rubbing to remove any
residue be careful with the smaller parts as a general rule don't let mask
part soak for a prolonged period of time then rinse well with clean water
allow all parts to air dry out of direct sunlight and heat
before you put your mask back together make sure all parts are clean and dry
start by reassembling the parts of the elbow gently insert the valve back into
the valve clip check that it is sitting well in the corners now with a valve
facing up slide the membrane into the slot and push the clip into the elbow
make sure both sides click this may take some practice now attach the assembled
elbow to the mask frame next you need to fit the cushion clip into the mask
cushion starting with the grooved edge at the top and securing all around
check that the cushion is not twisted or distorted
now align the colored tabs to the mask frame and push them in starting with the
side tabs then the bottom one make sure all three clips click into place
press on the edges to secure all around
to assemble the forehead support simply push the pads back in
then squeeze the pole in the middle
a-line and slide into the groove
now turn the dial clockwise until it sits flush against the frame the
pointers on the dial should be in a vertical position now you can set it at
the position that gives you good comfort and seal but be careful not to
overextend
now insert the port's cap
next slide the straps through the slots on the side of the forehead support and
reattach the lower headgear clips when it's time to use your Mirage Quattro
again reattach your swivel and it's ready to go
now it's your turn pause the video here while you practice reassembling your Mirage Quattro
with proper cleaning and care your Mirage Quattro should continue to
provide you with optimal treatment and the highest level of comfort for you and
your partner for detailed information please refer to the user guide packed
with your Mirage Quattro to learn more about ResMed products and accessories
visit our website or contact your Healthcare Professional