Hi, DIYers.
Joe here from Alarm Grid.
And today, we're actually going to show you
how to interface an August Smart Lock with a security system
through Z-Wave.
The Smart Lock, the third-gen, does have a Z-Wave module
inside of it and you can actually
interface it with your alarm system,
assuming that your alarm system has a Z-Wave module or Z-Wave
controller installed, and that it's compatible with the August
Smart Lock.
So before you do go out and purchase one of these
and try to set it up with your system,
it's a good idea just to check out your system
or call your security provider just
to make sure that your system has the necessary equipment
installed in it and that it's going
to be compatible with the lock.
Because the lock isn't cheap, I would say,
so before you do go out and purchase it,
just make sure that it's going to work
with everything that you're looking for it to do.
Today, though, we already have the lock set up,
and we already have our account set up in the August smart home
app.
Before you go to do your Z-Wave inclusion with the lock,
you're going to have to set it up with the app,
get that synced up, and then update
the firmware on the lock.
This will prompt you as you're going
through the app, so don't feel like you
have to go through the app and search
for these exact functions.
This is going to go through this process
when you do set up the lock and when
you do go to the Z-Wave menu.
Today, we're going to take the lock
and we're actually going to interface it with our IQ2 panel
up here, so let's show you how to do that.
The first thing that we're going to do
is jump into the app on our iPad and go to the proper menu
that we need to navigate to.
So on our iPad, we're going to open up the August app.
Click on our lock.
It's connecting right now.
We're not going to calibrate it, as it's sitting on the table
and it's not installed in the door.
So I'm going to click on Cancel, click on the gear,
and then click on Lock Settings right here.
I'm going to scroll down and click Z-Wave Settings.
And as you can see, it says, your lock
is not connected to a Z-Wave hub.
One thing that you won't have to do with an August Smart Lock
is perform an exclusion on it before you
perform an inclusion.
On a lot of Z-Wave devices, you're
going to do this just to clear out any programming that
may be in the device before you include it to make
the interfacing a little smoother and easier
without any issues.
The August Lock, though, because it's such a smart device
and it's communicating right with the app,
it's going to tell us if there's anything going on.
As you can see, the lock's not connected to a Z-Wave hub,
so we're ready to interface it right with our alarm system.
So I'm going to say, Add to a Z-Wave Network.
It's telling me, please put your Z-Wave hub in inclusion mode
before continuing.
So on our IQ2, I'm going to slide down from the top,
click on Settings, Advanced Settings,
enter the default 2222, click on Installation, Devices, Z-Wave
Devices, and then Add Device, and then
click on Include to put the system in inclusion mode.
Then on the tablet, my hub is in inclusion mode
so I'm going to click on that.
As you can see, on our IQ2, it has discovered the lock
and it's in the process of setting it up.
And there you go.
You can see that we have our information for the lock.
I'm just going to name it.
Let's call it the garage door.
And it's good enough.
I'm going to click on Add.
Whoops.
Already have a garage door.
Let's do the back door.
As you can see on the tablet, it says,
you are connected to a Z-Wave hub that's
using the S0 security protocol.
August Smart Lock Pro supports the new S2 protocol,
which we recommend for the high security.
This isn't going to give us any issues in operation,
it's just telling us that the Z-Wave controller
in this particular alarm system is
a little older than the one that will give you
the maximum amount of security.
But again, it's nothing really to worry about.
So I'm going to click OK.
It says, your lock has been successfully connected
to the Z-Wave hub.
I'm going to click Done.
And then if we go to our system itself and I click the Home,
and then I slide over, front door.
Back door.
So there you go.
So you can see that the lock is actually
connected to the system via Z-Wave,
and that everything is working.
If you do have any questions about this process,
though-- connecting your August Lock
to a Z-Wave compatible or a Z-Wave hub,
your security system, how to interface it,
or what features you're going to get
from using this particular lock with your service,
feel free to give us a call at 888-818-7728,
send us an email to support@alarmgrid.com,
or head to our website, www.alarmgrid.com.
If you did enjoy the video, feel free to subscribe.
And if you want to be notified when we post future videos,
hit the notification button below,
and we'll send you an update when we do so.
Thanks for watching and have a great day.