In a previous video, I made a whole lot of tool holders
to go on this wall but I still have a lot of blank space.
And I also still have a whole lot of tools
that I still want to mount.
I'll start with a drill press vise
and that's gonna go on a piece of plywood,
with some hooks to hold it.
I sanded these blocks down a little bit
and now I just need to glue them
so that when the vise is hooked on there,
these go right in here.
So I decided to just put the vise on there
to make sure they're exactly positioned right.
And now I'll just leave the glue to dry
while I work on something else.
For all these tools, I think I'll arrange them like this.
And I'm gonna have a shelf that some of these tools
go through and then an area behind
to have hooks for like this and this and this and this.
I'm gonna mark where I'm gonna cut the slots
in the shelf for the hammer handles,
and for the square.
Need about this deep for this one.
And for the hammer,
the hammer goes about this far back.
It's such a pleasure working with a freshly sharpened
bandsaw blade.
While the glue dries on that, I'll work on some holders
for these hand planes. The hand plane is gonna go
on this board.
But rather than relying on magnets
or putting this board at an incline
to hold the hand plane on,
I made 2 L-shaped rails that are gonna
hook it on, like so.
But I need that shape of the rails
to match the form of the plane.
So, here's the line and I need to remove
all of this stuff.
Now, how to remove the rest of this stuff
without having to chisel it all?
hmmmm... So, here's my idea.
If I run this piece along the saw angled
just a little bit like that,
I should be able to cut most of that.
And to run it like that, I should run it along the fence,
with a shim here because I don't want to make a taper jig,
And if I set the blade to be about this far from the fence,
then I should clear most of this.
So let's set that up.
Arrgh.
Now I just gotta make that shape a bit more elegant.
Finally got these two things whittled to their final shape
so I can now glue them on.
I just made two more pieces to hold this small plane.
And the holder for this one is dry now.
When putting the plane in here,
there's a tendency for it to get really wedged in there
because this is tapered.
So to prevent that from happening,
I'm adding these two screws here.
And now it never becomes tight.
And I also carved a notch right here
to prevent the blade from getting caught up
when its being lifted out.
The glue on this vise holders been dry for a long time
and I'm screwing it on, right through the hooks because
those have to hold the load.
The glue on this thing is long dry now
and I've laid out where I want the pieces.
Just got to mark where the screw holes go.
I'm using dowels to hold up the hammer.
This dowel here is there to make sure that the squares
stay on square instead of hanging down, like this.
I've had it happen before as I'm banging away at things
on my workbench, vibrations get transferred to the wall
and the hammer eventually slides forward
and as I keep banging,
it falls on my work.
So, I added these two indentations
to the bottom of the hammer, and these two screws
so it interlocks and it won't wander forward.
These two little blocks, here
keep the marking gauge from moving forward.
And I've got the block here that keeps the square
from sliding off.
To keep the hammer from sliding off of these
they're slanted up just a little bit and
I have a shallow notch carved in the top.
I figured up here would be a good, safe out of the way place
to keep the dial indicator. But to keep it from falling off,
I made this little lock that holds the top of it.
I made this block with some holes drilled in it
and some slots cut with the bandsaw,
and that's so I can put these knives in here.
I made this little shelf a lot like my other tool holder
so I didn't film it. And this ones for holding
my tape measures and pencils.
If you are gonna build tool holders like this,
try not to do it all at once because
its a surprising amount of work
making all these little things.