Narrator: In 1987, the Ferrari F40
became the first street-legal car to go 200 miles per hour.
In 2005, Bugatti's Veyron hypercar
broke the 250-mile-per-hour barrier.
In late 2019, The Bugatti Chiron Super Sport
became the first production vehicle
to ever reach 300 miles per hour.
But why has it taken almost 15 years
just to go 50 miles per hour faster?
Andy Wallace: You think about speed as a linear measurement.
And I suppose it should be to a human brain.
But if you've ever gone 150 miles an hour before anywhere,
if you then step that up just to 180,
it's only 20%, but the difference is huge.
Narrator: That's Andy Wallace,
the driver behind Bugatti's 300-mile-per-hour run.
Andy: Aerodynamically, downforce, lift, drag,
it's all increasing exponentially as a square of the speed.
If for example you had a car
that was capable of 270 miles an hour,
the efficiency you need to take
that same car up to 280 is pretty massive.
Narrator: The power needed to overcome
a force like drag, or air resistance, is most intimidating.
The force required to push an object through the atmosphere
increases at the cube of velocity.
To translate, a car that needs 200 horsepower
to overcome aerodynamic drag at 150 miles per hour,
would need 1,600 horsepower,
or eight times as much, to reach 300 miles per hour.
But to build a 300-mile-per-hour car,
it's not as simple as a monstrous engine.
First, you need to start with the tires.
While they're not the most complex car part,
as the only part that touches the road,
tires are one of the most important.
And at 300 miles per hour,
when a puncture or blowout can end in disaster,
they mean everything.
At that kind of speed,
the Bugatti's tires, spinning 68 times per second,
had to withstand 7 tons of tearing force
trying to rip them apart.
For an idea of just how intense that is,
the tires on a Porsche 911 driving full speed
only experience about 3.
Andy: One of the things you need to do
is you need to stop the tire from changing shape
because these enormous tearing forces
would actually make the tire crowned on the top.
The tires were not totally different,
same carcass, same molding, as the standard Chiron tire.
But what they did do is reinforce
the very last steel band that goes on the tire
before the rubber goes on.
I think the tricky part was they didn't want
to increase the weight of the tire.
Narrator: To do this,
Bugatti chose every engineer's favorite
weight-saving material: carbon fiber.
It can be 10 times stronger than steel
but five times as light.
After adding a thick layer on the tire's carcass,
the layer of rubber below the tread
that's responsible for absorbing shock,
Bugatti's engineers had to test it.
To make sure the tire could handle 300 miles per hour,
they brought it to Michelin's aircraft test center
in North Carolina.
Using the same test bench used by companies like NASA,
they found that it could handle
up to 318 miles per hour before warping.
But even the strongest tire means nothing
without the power to spin them.
For an idea of just how much power is needed,
look no further than one of Bugatti's biggest competitors
in the race to 300 miles per hour, Hennessey.
The company's upcoming Venom F5,
estimated to reach 301 miles per hour,
houses a 6.6-liter V-8
that makes an astounding 1,817 horsepower.
To generate more horsepower,
an engine has to burn more gasoline
which requires more air.
One of the most common ways
to feed more air into the engine is through turbochargers.
The Venom F5 not only uses massive twin-turbochargers,
but it also manages to reach a very high RPM.
RPM stands for revolutions per minute,
and it measures how fast the engine is spinning.
In general, the faster an engines spins,
the faster it burns air and gas,
and as a result,
the more power it makes.
A smaller engine with smaller and lighter parts
can spin faster with more efficiency,
but has potential to wear out quicker from the speed
than a bigger engine with a lower RPM.
All of this has to be taken into consideration
when choosing an engine for speed records.
But in the end,
the biggest obstacle to 300 miles per hour is air.
The drag, or air resistance, that a car encounters
as it approaches this speed,
can be compared to what you encounter when swimming.
Christian Von Koenigsegg: The resistance increases
in square. So going from 200 to 300
is basically, roughly calculated,
double the energy that you're running into.
At around 200 miles per hour,
you get more into airplane aerodynamics
where you're actually
compressing the air in front of the vehicle,
and it takes different routes over the bodywork
than at slower speeds.
Narrator: That's why the goal of engineers
when designing a hypercar's body
is to eliminate as much drag as possible.
No car does this better
than automaker Koenigsegg's upcoming Jesko Absolut.
Based on the company's Jesko hypercar,
the Absolut is estimated to reach
as much as 330 miles per hour.
Similar to Bugatti's record-breaking Chiron,
it has a longer flattened tail.
This makes sure air flows off the car's rear seamlessly.
Without it, you have a higher chance
of separation in the airflow,
which would only add to the drag.
The car also improves other forms of resistance.
The standard Jesko features a massive rear wing
to increase downforce for those tight corners on the track.
But downforce on the rear wing
of a 300-mile-per-hour car
would only slow things down.
Ditching the tail reduced the Jesko Absolut's
maximum downforce from over 3,000 pounds to just 330.
To keep the Jesko Absolut
from flying off the sides of the test strip,
that massive rear wing was replaced by two small tail fins.
They may look tiny,
but they redirect the vortex of air
generated behind a speeding car
that creates turbulence.
And those sharply cut side vents
do more than just cool the engine.
Christian: They act like kind of small side parachutes.
They actually become kind of fully efficient
at over 200 miles per hour.
And the reason for that,
if they worked better at lower speed,
they would be too restrictive at higher speed.
They would be blocking too much.
Narrator: But as impressive as these
automakers' innovations have been,
none of it would be possible
without the way testing has advanced.
An aerodynamic simulation
that took a week to run 10 years ago
can now be done in three or four hours,
allowing new solutions to be tested immediately.
And while Bugatti may have already been
the first to reach 300 miles per hour,
automakers are constantly chasing the next record.