hello I'm Scott Brown with green wind another home energies this rod right here that I showed
you a while ago as I'm going to grind off a little sexually uses my pegs I go through
the four corners of my my winder to keep the coils where they can come off anyway
one thing I wanted to show you when I cut these circles out SkillSoft notice that edge is nice
and beveled and also you can see the lines where the blade past going like this because it's round
it beveled it out pretty nice which gave me a idea or something I never tried and I want to
try doing it the Dan Rojas style I'd have to say this circle I could probably use for a VAW
T this is the outside piece and it's a little thin towards the edges here I probably use a
bigger piece of plywood and play with that but I'm thinking of casting my state or into this
ought to pop out real easy and if I really want to I can grind the sides back down afterward
our systems outside the line just a bit outside the line over yeah
their coffee other people
I thought this would lay down flat
it might be a little bit
down the edge of this drill bit mother outside the wine from this wretched learning
same as the other one
file out afterwards
water
with the knife this way to make sure it comes out by going so far this way
this is a 15 30 second drill bit same diameter as my rod
line it up the other way
in the money
get our fire
victus and the other two place holder's guide line them up and drill
yup okay I've raised this up notice this goes all the way down to where it just
goes into the hole and pass the hole and this comes up I got one two three layers plenty of
room so now let's do this I'd rather do this one first because it has the lines
where I can line this up straight I'll put a peg through the middle matter of fact these
middle holes need to be drilled buzz that was done with the other bit let's do that first
hello I'm Scott Brown with green wind and other home energies as you can see right here this is
a piece of that rod that you saw with now I want to go ahead and turn this and show you
what I've done I went ahead and ground down the side leaving about a nine I should have
had the curve going this way since this rotates this way but backwards works fine but this drill
here doesn't go into reverse anyway because the other drill bit was just a little bit thinner
than I wanted it to see that edge is still sharp right there and basically I stuck the rod inside
here I took my angle grinder at an angle and held it there till I got a nice point and then ground
down carefully to make it go right to the tip and so far after sticking one more piece right
here and a screw right here yeah a couple chips out here because I was pressing down a little
hard but it drilled right through and you can see those pins are going to fit pretty snug
but they're going to fit straight and they're going to fit nice anyway I'm going to go ahead
and take this down and I'm going to go ahead and drill through the other part and then I'm going
to go ahead and I'm going to go ahead and drill through the other side with this together which
means I'm going to take this screw out or drill one from the other side in and then push this
pin through flip it over put the other piece on and drive that other one in a little farther and
I'll come right down these same holes and drill through the other one and everything should line
up and be straight if you don't drill through here into here your holes might not be in the
same spot they're going to be tight and wrong so this is the main way to do it use this as your
guide drill in makes your holes you know all of these are lined up with the other ones and then
when I flip this over and put the other one on the other side I'm going to drill right down
through these holes and drill the other side of the form okay you see I don't have the other set
up over here I want this on this side basically what I'm going to do is use the holes right here
set these down inside there I got this one pushed up so that's going to be alright and all I got to
do is find a place for this one to set as I put another screw from this side to keep this
exactly where it's at and then take this one out then I'll take that one from this side I'm
sorry from this side and shove it right into this one to now be right back in a minute okay
well and now I got this screw and you can see the hole from the other screw right there and
this I'm just going to just tap right on down the other piece there he is it's all the way
through and put this screw down the rest of the way just a whoop not exactly all the way down
think X yep they're real tight to each other I'm sticking out the other side
just a little bit that sound you hear on this one through got it sometimes you use
a little impact and everything is for doing drywall it doesn't just
muscle it through it puts it through with some vibration all right now it's time to
drill this other one I'll get that set up that should set us up let's drill a hole