i'm going to be putting one of them in the cyber power
i 7 11 700 to replace the stock venison and it's awful and i'm going to just weigh each
one and we'll see what the weight is so this is the original rgb black edition pounds 5.2 ounces
the hyper 212 evo version two two pounds 2.7 ounces so it's a little lighter
and this is the arctic freezer
34. which feels a lot lighter but is actually two pounds 1.9 ounces
so it looks like it's the smaller weight of all three
so this is the stock fan and the cyber power machine
i'm getting 95 100 um celsius just running um some video video editing
scanning for viruses things like that so this this fan is unacceptable and it's coming out
now it has two plugs one goes to the motherboard and one goes to this the back side of the case
the back side of the case is the rgb the freezer 32 here doesn't have rgb so i'm not going to be
using that i'll just take that um cable off and we're going to just see what happens so this is
the back plate that i don't want to take off it's already got an existing back plate for that cpu
hopefully i won't have to touch that and i don't want to touch that because here under here is some
3m tape if i had to i could put um some dental floss heat up this a little bit and then pull
that out but i really don't want to do that and um i'll take the um rgb cable off that's down
this is what i'm going to use to clean the cpu after i pull it off i'm going to pull
the screw on the bottom slightly loose then that one and that one and that one all four just loosen
them and then take them off individually with your this is what the original um
paste looks like on when you take it off looks like i got decent coverage
show you that the um screw bases and the existing back plane for the original system all flush
to the motherboard this is what you get in the case it comes like this the fans are
already attached with the cable your parts are in a bag this is the back plane notice
how it doesn't have the spikes sticking up the screws it's just basically a flush
installation like we have now so it should be compatible hopefully and then you get two cards
so here's all the parts you get after you open the bag there's three of those
actually i pulled one out i think you use these larger ones i'm gonna look in the
instructions the instructions are actually online the good thing about this is these
i'll show you real quick you just screw them
into the existing backplate that the original motherboard and cpu cool used
they they're a perfect fit for it you see that
site say revision one revision two um there i mean three there's no two
i selected revision three i don't think the instructions are gonna be much different
i'll probably look at both revision one and revision two since they don't have a revision
um two i mean um it asks you what cpu you're using and then it says preparation remove the old cpu
make sure you have the coolant orientation which i should check first to see if it's going to fit
and then i'll do the installation okay i test fit the fan and the cpu cooler in the case there's
plenty of room it clears both all four memory slots on the power cyber power machine and the fan
clears the tops case no problem so this is going to fit in your cyber power machine no problem
with the two fans here's a little animation they give you basically i'm gonna do a back exhaust
i think it's the first one there's four of them to choose all right here's the difference
between the revision 2 and revision 3 in the install supposedly i guess
here's the instructions for the system with the lga 1200 and revision2
there's some washers i guess
okay basically they tell you in this little animation to put the washes on first
see the washes and then you put the um the mount on top there's the washers there in these little
um plastic washers so you put that on before you put the um little turn nuts on these things
i don't think revision one came with the washers so revision two which it says is what what came
with the washers i missed this in the instructions that's the one that you have to use for the um
lga 1200 the larger one looks like the smaller ones you don't use for this so that's a good sign
i'll take a picture too okay i put the four um studs in there and i put the washes in the
washes have a little sticky stuff on the bottom so when you put them in it's gonna stick to the board
which is good and i just hand tightened them i didn't do any mechanical tightening about this cpu
cooler from arctic um 34 is that you don't have to touch the the back plate of the existing um
cyber power system is just wipe the material off and then at the end i'll use the alcohol on it
all right they have instructions on youtube by artik uh and the guy put a whole bunch of um
of the paste on the actual heater core but in the instructions on site that online that they
give you there's only a dot in the middle which is what i'm gonna be doing i'm gonna put a small
p size maybe a little smaller than the p dot in the center of the cpu
all right i put a little too much but that's fine okay the next part is to put these um
plates on i'm gonna look at the instructions on how to do that
i wanted to let you know that you should probably take a picture of the side view of this and see
how the spring is holding the fans on because you're gonna have to take those fans off soon
okay this part is pretty simple um there's a little slot so you make sure that you put the
um device in there correctly i'm gonna look at the instructions make sure i'm doing it right
okay to get those things on you had a those mounts on you had to take the fans off the
fans aren't easy to take off okay one thing you don't want to forget is to take this plastic
thing off the heater core because guess what i did
that's what i did okay i got it in here and i'm gonna just tighten the screws counter one on this
side one on the top one on the top one on the bottom and i'm just going to tighten it slowly
each turn maybe one turn of the screwdriver each time and just keep going back and forth until
i think it's settled all right it's in there good i just tightened it tilt stopped stopped
turning i didn't over tighten it hopefully
putting the fans on now the fans are going to be trouble i think by the way i have my
video card moved to the third slot and it gives me a lot more room to work in here
i wanted to show you the fan um see how there's a sticker on this side and it's not on this side
the sticker is going to be facing to the right of the memory
that way it comes in and flows out like that
all right on that emblem on the fan this little sticky um clear plastic
coating you could just pull it off it'll be hard to get off later so i'll do it now
okay i got the one on the right side in start from this side it's the hardest side
um at first i didn't think i got this in but i got the other side in properly
and make sure that the um the these are both facing this direction to the right
so the next one will come in the same way as this one is you want the airflow going out
make sure this cable is in the slot here it pops out you want to be flush with the cable
all right i got both of them in there okay i'm running fur mark right now it's running the
cpu at 100 percent and so far we're getting the highest to 70 c
on the cpu we were getting 95 100 before i switched out the um cooler
um fur marks pretty aggressive as far as pushing that cpu to the limit of a hundred percent
um so you're seeing that i'm getting the most 70 degrees this has been running for about
20 minutes now too i was getting 90 100 so this cpu cooler brought it down 30 degrees from the
stock cpu cooler that came with the cyber power machine um i'm also going to do a video at the
same time and see what happens let's we're running this fur mark at full intensity now
it's doing really well i mean we're at 100 here you can see on the test manager
it's at 4.13 on speed but see it's doing the video at the same time
so it's doing the stress test plus up making a video at the same time i don't expect the video
to go very far as far as completing because this guy is eating up all the processing time right now
gpu is running at 57.51 degrees 56 utilization right now so this is a really hard stress i
could even throw in this how about let's do a virus scan at the same time on c drive
and that thing usually pings it to 100 mega 100 degrees right there alone that guy
and look our cpu is not even feeling it
no let's go here yeah we're still running pretty well
full speed 4.15 that's pretty close to full speed cpu's never hasn't gone over 66 degrees
since i restarted core temp and it's still doing the fur mark stress test and creating a video at
the same time and scanning the hard drive i was getting a hundred here constantly on one of these
items not on three of these items but if i ran one of these it would get a hundred now it's getting
63. so that arctic cpu cooler i have is doing its job unlike the stock cpu that cyberpower gives you
and i'm going to be running more tests like this in the future i'm going to be setting up gaming
and i'll do some tests on gaming this is actually more stressful than the gaming will ever be though
How to Install the ARCTIC Freezer 34 eSports DUO