Smart film is an innovative window treatment
that instantly transforms ordinary glass
into smart switchable glass.
Installing smart film is easy
if you follow the instructions and
avoid making common mistakes.
Watch this video now to see step-by-step
smart film installation.
Step 1: cleaning the installation environment
did you know that 80 percent of smart film
installation mistakes are due to improper cleaning.
Ideally, the installation area should be vacuumed
to ensure there is no debris that can stick
to the film because it is very static
and will attract dust.
Step 2: Unpacking and testing the smart film
remove the tape unpack the film
and carefully lay the smart film pieces flat
with the self-adhesive layer facing up.
Next, test panels by connecting them to a controller
to ensure they are in working condition.
Step 3: double check the sizes to ensure that
the smart film pieces are the correct size
by measuring the glass and film.
If the film needs to be trimmed, do so with a pair
of tailor's scissors or blade prior to installation.
Step 4: clean the glass and film.
The glass must be extremely clean
before you apply the film.
This goes beyond simply wiping the glass.
Clean the glass with alcohol and a lint-free cloth
in good lighting to ensure all dust and streaks are removed.
Run a blade across the glass to remove any debris
inspect the glass thoroughly to make sure it is perfectly clean.
Next, clean the self-adhesive side of the film
to avoid transferring dust from the film to the glass.
Step 5: removing the protective liner and taping the edges
tape the corners of the protective liner at the top
so you can easily pull the liner down throughout installation.
Now, peel back the first two inches of the piece of the film
and secure it with a piece of tape so that the
protective liner will not stick to the film.
Step 6: Carrying Smart Film.
Never bend or fold smart film.
For best results two people should be carrying the film to prevent damage.
The film can be carried in a u-shape,
never bent into a v-shape,
and it can also be carried by one edge.
Step 7: Applying the smart film to the glass.
Fit the film to the top of the glass area
and then align the bottom and sides so
all the corners and edges are properly aligned.
Stick the first two inches of the film
to the glass and confirm once more that the film is properly aligned.
If not, peel it off and realign.
Once you have attached the top two inches the rest is very easy
as you can see we're pulling on the tape ends to peel off
the protective liner ideally you should not peel off more than six to eight inches.
If you do more the film will adhere to the surface of the glass under its own pressure
and most likely will create bubbles.
Never go too fast or apply too much of the film at once
use a squeegee to make sure there are no air bubbles.
Adhere the film two inches at a time and watch for bubbles
if bubbles do form there may be dust under the film.
If this is the case mark the area peel back the film and remove the dust with sticky tape.
Check the glass as well to make sure it is clean and then
reapply the film and continue with the installation.
Repeat this process until all the film pieces have been installed.
Step 8: Wiring the Smart Film.
Now that the film has successfully been applied to the glass it just needs to be wired.
Both smart film and smart glass have two wires
that get connected to a controller and
because it works on AC there is no positive or negative,
which makes it even simpler!
Now it is time to test the film to ensure that it works following installation.
Hide the wires for a clean look.
For details on how to conceal the wires and other wiring solutions please watch our video
'How to Wire Smart Glass and Film- Smart Glass 101.'
Step 9: Sealing the Edges with Silicone.
Use a neutral cure silicone to protect the edges of smart film from moisture and damage.
An acid-base silicone will corrode the film.
How can you tell if you're using the wrong silicone?
Smell it. If it smells like vinegar it's the wrong type.
Apply the silicone and remove any excess.
Peel the protective liner away from the edges or completely remove it before the silicone dries.
if you remove it after the silicone is dry you can
break the seal that prevents the moisture from penetrating.
Step 10: Enjoy Your Privacy on Demand.
Now that the film has been installed and wired
you can switch the glass from clear to frosted
whenever privacy is desired.
Switchable glass products instantly modernize any space.
Thank you for watching we hope you found this video helpful
if you have any questions please contact us.