Hey!
How's it going?
Mike from 1A Auto, and I'm going to show you how to remove the door panel, remove your
speaker, reinstall a 2015 Chevy Silverado—pretty much the same as a GMC Sierra.
If you're going to be working with the doors open, a good idea—this switch, right up
here, shuts off your dome light.
Middle position is on with the doors open.
Over here is permanently on, and then you can see the lights, right here.
Shut it off.
That way your lights aren’t draining the battery while you're working on your door.
First, you're going to want to remove these little doors.
There's one here, and there's a little indent down at the bottom.
You want to use a little 90-degree pick, available at 1aauto.com.
Pull the bottom of that out, and then that panel comes out, and then there's another
one, right down in here—the same thing.
There's an indent at the front.
Work the pick right in there and go down first, underneath; pull it up.
Now, this panel comes off, and this one can be a little unnerving.
You just have to pull hard and it does release.
Sometimes these metal clips will fall into the door, but you actually want to retrieve
them.
And you can do it just by squeezing them and prying up with the screwdriver, and then down
with my finger.
And sometimes these will fall down into the door, and you just have to wait until you
have the door panel off to retrieve them.
But you can just push them right back on to the panel so that when you go to reinstall
it, they're there.
Now, six 7mm bolts hold it.
There's one way back in here, one right up here, two down here, and two at the bottom
of the door panel.
And I'll remove those.
Use a 7mm socket with a ratchet and an extension.
Alright.
So, we've got the six bolts out.
This part can be the worst part because now it's just clipped in place, but these clips
can really hold on tight sometimes.
I just work my hand underneath this corner and then I grab right here, and I just give
a good pull.
Okay.
And there, there's clips all the way up at the top that release.
The door panel comes off and goes up.
Release your door handle cable by pressing down here and then pulling back.
Okay.
And then work it around, pull it up and out.
And then, there's a single electrical connector, here.
Push on the black tab while you pull up on the gray tab.
Okay.
And then bring the gray locking tab out, and that unlocks.
If you did pull the panel up and off, and this weather strip went with the door panel,
you're going to want to remove this piece of weather strip.
Pull it down.
And you can see some clips back in there.
And pry down with a small screwdriver and then pull up to release each clip.
And you can see the clips actually come off as we go.
The speaker's just held in by one 7mm bolt.
Remove that.
Lift it up and out, and then it disconnects by pressing this tab down and disconnecting.
And then, just pull this back and forth, up and down to release it.
Then, if you have the correct tool from 1A Auto, it makes it a lot easier.
Work it on there.
Alright.
Reinstall, reconnect lead, put the clip back in, and put it down into place, and snap it
back into place.
And a single 7mm bolt secures it.
If your door lock fell out of place, just put it back up into place.
And then, these clips slide back down onto the door, and the weather strip goes back
in place.
This part seals against the window.
Now, your panel—put the door handle cable on first.
Put it down in.
Pull back around, and then slide it forward into place.
And then, your connection, down her—lift up.
Put the connection in place; get it going, and then slide or pivot that locking tab up.
And there's two larger line-up pins—one here and one on the front, here.
So, just kind of lock things into place.
Make sure you lift this up; put your lock into place; down, and then I can see that
line-up pin, right there.
And then, this front line-up pin, there.
Okay.
And it locks into place.
Now we're going to put our six 7mm screws back in.
Alright.
One was here, one here, two here, and then two down low.
This one, that we're going to put in here—just going to put a little piece of paper towel
on there; hold it in place, and put it in.
Start it going, and I'll start the rest of them.
Alright.
Now we'll tighten those up.
And you don't want to get these too tight.
Get them nice and firm, and that's good.
They're only going into plastic.
The panel's back in.
Curve the soft corners at the top.
Pushes into place, and then this little notch goes in the front into place.
And then, this panel—once you've put your clips back on, you're going to put the top
up and in, and snap it back in place.
Thanks for watching.
If you want the parts to do it yourself, check out 1aauto.com: The place for DIY auto repair.