[music] Messick's,
a helping hand with your land.
Neil from Messick's here,
out to talk to you today about rototillers
and everything you probably ever wanted to know,
and then some.
We're going to talk through four
different things here with you today.
We're going to talk through the features of a rototiller
if you happen to be shopping for one.
The operation
of one, if you're actually outputting it into the dirt.
The process that you need to go through in order
to attach it onto your tractor,
and some maintenance tips if you own one today.
We'll start going through features of a rototiller.
Generally, when you're sizing a rototiller to a tractor,
you're going to be looking for one that covers
the rear wheels of a machine.
I've got this here pin on the back
of an MX Series tractor.
I picked this tractor because it's one
that we operate in rental fleet, so I can get it dirty,
and this tiller is also our rental fleet tiller,
and it oddly happens to be
a little bit small for this tractor.
This is a Woods TS60, a 60-inch model.
This MX tractor, if you pulled a tape measure
across the back, you're going to find it's right about 68 inches
across the rear wheels,
but you can actually get away with that.
A lot of these tillers you're going to find can offset.
In the case of the Woods right here, you'll notice
the points here that the three-point arms attach onto the tiller
can be loosened and side-shifted
left to right.
Side-shift is a feature that you won't
find on all rototillers,
so if you think you might be taking your
attachment and shuffling it
between tractors,
that side-shift can enable you
to be able to go up or down
through different models and still be able to cover the tire track
at the back of the tractor.
You want to be able to do that because as you're going back
and forth running your tiller, you don't want to be
driving over top of the soil that you just tilled.
It ruins the seedbed that you're trying
to make as you're running it.
You want to look for that feature,
that side-shift, if you're going to be doing that.
Tillers are driven by the end.
Generally, you're going to have a shaft coming back and a gearbox.
That gearbox is going to turn the power 90 degrees.
It's going to go out to the end of the tiller,
and then the power is going to drop down
to go down to the tilling mechanism on the bottom.
You're going to find two different styles of dropping
power down on that tiller.
It's either going to be a chain drive
and an oil bath down here on the end,
or gear-driven with
generally four different
gears down there in order to transfer that power down.
Had a funny conversation with a
tiller manufacturer about that actually.
Gear-drive tillers are generally
a little bit more expensive
than their chain drive counterparts.
The tiller manufacturers will tell you that's
money that's not worth spending.
By and large, they were
happier with the older
chain drive systems
than they have been with the gear-driven ones.
By and large the reason why
gear-driven tillers are being
offered by most companies today is
the perception that you and I would often have
of gear-driven systems
being better than chain driven.
Advice for the tiller guys,
don't spend the extra money for the gear drive tillers,
the chains are just fine.
Haven't seen problems from the gear drives either,
so if you've got one today, you've not made some kind of huge mistake,
nothing to run away from there.
Tillers are sold in two different variants,
either forward-rotating tines
or reverse-rotating tines.
This version here is forward-rotating.
Those two different systems are going
to till the ground very differently, so
by and large, you're going to find most tillers are
the forward-rotating variety.
The forward rotation, because of the way that they spin,
if they hit rocks or those kinds of
things,they catch debris in the field,
they're going to bounce up on top of those things.
It's going to take that big rock,
push it down into the ground,
and right up on top of it.
The backward-rotating version is going to take
any debris that it finds and pull it up
into the shield, into the tiller itself.
If you happen to catch a log or something
that you didn't see out there, a tree limb, or a big rock,
it's going to pull it up into the machine
and bend up the inside of the tiller.
Why would you buy
a reverse-rotation tiller?
Because the tines are running backwards,
the tiller is pulling in the opposite
direction of the tractor and it's also
pulling itself down into the ground.
If you're trying to go into say,
virgin soil, it's going to be more aggressive
and it's going to get down into the ground a little bit better.
It's also going to take that soil and throw
the soil up on top
and give you a little bit nicer
finish at the end than what a
forward-rotation tiller does,
just because of the direction that the tines are spinning.
Reverse-rotation, if you know where
you are and you're working in established areas,
is going to give you a little bit nicer finish coming out the back,
but by and large, you're going to find
the forward rotation variety being a lot more
popular and run a lot more,
because we just don't have the damage
concerns that we do with reverse.
Received a lot of questions from guys
often unsure of how to do their three-point hitch
adjustments for various implements.
A rototiller is one of those
things that I like to have
tight but not too tight,
if that's a way to describe it.
You want a little bit of side-to-side
play in a rototiller, and that's
because if you have this thing dropped down into the ground
and you go to turn your tractor,
you don't want to bind it up while it's down there.
A little bit of side to side wiggle,
what we've got right here would be desirable,
but you certainly don't want to have so much
that the thing's going to slop around behind the tractor.
That can get annoying, too.
As far as your top link goes,
you're going to want to rotate this guy
until the skid shoes on the bottom of the tiller
are more or less level with the ground.
Not necessarily to get out your bubble level
in order to do this one, you can eyeball it just fine,
but generally, there's some skid
shoes down there that are going to be used to adjust your height.
You want to set those shoes more or less flat.
Talked earlier about this side-shift
being a feature here.
I've got the side-shift set up here
for about two inches
on the back of my MX just to get this thing a little bit
closer to the outside tires because
my tiller is not covering the footprint
of my tractor so you want to eyeball that up, too.
If you're getting your tiller out for the very
first time in the course of the year,
there's a couple of things that you should walk around
and put eyes on, just from
a general maintenance and ownership perspective.
You're going to have two oil baths in here,
the central gearbox,
and the gear case down here in the end,
whether you've got gears or a chain,
you're going to have oil down here in the end.
Both of these things are fairly low tech.
They're going to have a
check plug and a fill plug
and you're just going to basically open that up
and make sure that you've got the thing good and full of oil.
These kind of gearboxes aren't going to be super picky about
the kinds of oils that you put in there, so
as long as you've got some decent gear oil,
you're going to be just fine.
Tillers are going to have a slip
clutch on them in order
to allow those tines to slip.
If you do come into some kind of obstruction,
you can eyeball the slip
clutch down here inside the shield.
A good idea annually
is to take this slip clutch
and force it to slip,
because if these things are left
to rust up,
they'll bind and then you have no
protection back to your tractor's drive
line at all.
Especially if you keep your attachments outside,
you're going to want to run through some slip
clutch adjustments. I've got
separate videos here that will talk you
through on exactly how to do that,
but you want to put eyes in that slip
clutch annually.
Right and about, the grease gun is
always going to be ideal,
a good idea. You're going to find a bunch of Zerks
on your PTO shaft,
and if you have U-joints,
depending on what the shafting looks like,
going back to your gearbox,
out to the end of the tiller,
you want to put eyes on that.
Some models will have those
in the U-joints, but not all will.
If you've got any kind of twine,
or plastic, or stringy debris,
your tiller is going to find it
and it will end up wrapped
back here in around the tines.
It's a good idea to get down here and put eyes on these
things and pull any of that kind of stuff out
as soon as it accumulates down here,
especially if it's pushed up against
the bearings at the end.
That kind of stuff putting pressure and pushing
back into the bearings is what causes
seals and stuff to pop out.
Always make sure if you caught anything in here,
you do your best to get in here and get that cleaned out.
Also, on those big bearings on the end,
you're generally going to find grease Zerks,
so while you're hitting the top of the tiller with your grease gun,
you want to look down here on
the underside as well. You don't want to miss these.
We're going to go and till up two different areas here,
just to give you a little idea of what this looks like.
I'm going to go turn, basically
grass here. If you were starting a garden
for the very first time,
we'll do a short strip over here and show you what
you can expect from a forward rotation tiller.
We also got a really
compacted area over here
that's frankly a road.
We'll go and till that up a little bit and just
see if we can get this guy
to bite down on the ground and loosen it up a little bit.
Come along with me. We'll see what it does.
You see here as I'm going,
I'm getting a lot of grass. This is
a bit of a yard.
My depth
setting on the tiller is to drop it
down the entire way,
but it doesn't look like I'm really
quite that deep. When you're going into something
like this for the first time,
tilling it multiple times is pretty much necessary
and each time you're going to get the soil a little bit looser,
so those end plates are going to be able
to drop further and further down into the ground.
This reverse pass is when
it's nice to have and tiller that's going to cover your back tires.
I said I'm running an offset on this,
but even with an offset,
I got to go in and circle
all the way around to the other side if I really
don't want to drive across where I've already been.
There, I caught a rock.
If you're watching the tiller there,
we caught a rock or something hard underground
and the tiller bounced,
It jumped up over top of that rock.
That's the time where if you've got
the reverse rotation pillar, which
is going to be a little bit more aggressive,
it's going to pull this up down into the ground,
that rock wouldn't pop up into the hood.
We do sell a fair amount of reverse rotation tillers.
Like I said, you just want to be mindful that
that's a piece that you're running in a
ground that you're familiar with.
It maybe hard to see it, but from my vantage point now,
I can see that my tiller's
a little bit deeper than I was before.
One thing you want to remember here when you get
to the end of your rows is to lift
before you turn.
You have your tiller setting down
into the ground and if it's embedded in there at all.
When you make your turn,
it's not going to track immediately
behind you and you'll be trying to push it left or right.
It's always a good idea to lift
ground the gauging implements
before you turn your tractor.
You can see here a couple passes back and forth
at that tiller and I've got the soil to a point that it's
more than adequate for coming in and starting
a garden or something like that. I've got
a couple of inches of nice loose topsoil.
After a little while, this grass is going to start to die off
and coming back through here in another week or so,
probably wouldn't be a bad idea if you're really
actually going to start something as a garden, but
just a pass or two out here does the job.
You can see I did find some rocks and stuff in here.
We talked about forward versus a reverse tine.
Starting ground like this for the first time,
the reverse tine is going to be more aggressive
and the dirt's coming over the top.
It is going to finish a little bit better,
but this stuff is where you're going to run into a problem.
Just be mindful if you are looking at that reverse-tine tiller,
they have their place in established gardens,
but for what we're doing here today, that
forward tine is going to be the way to go.
Come along here with me.
We'll go up and run this guy in a road up
here a little bit too, and see what it does.
We have a wash out
here when we run some equipment back and forth, and I
honestly, this might be a bad idea.
Usually you'd want to come through here with a ripper or a land plane,
a box scraper, something else to loosen
this thing up,
but it's hard and it's compacted. I thought it'd be
interesting to see what the tiller does.
We're going to take it over here
and lower it down a little bit and we're going to run
the engine a little bit slower.
It's going to bounce around a little bit.
That's a little bit more rocky that I want it to be.
You can see there the need for the slip clutch though.
As I was sitting here watching the PTO shaft go,
you're looking at a plastic
shield on the outside, but the slip clutch
plates are back inside,
and I visually could see the slip
clutch there going as we were hitting.
In rotary cutters you have the choice
of slip clutch versus shear pin drive lines.
In tillers though, you're pretty much
always going to want slip clutches.
I'm not even sure how many companies would even offer
this to you in a shear pin. I hope there's none,
but given the type of work that these things do,
you're going to want that slip clutch in there because
it's got to be banging up in
all kinds of stuff that you're going to find in the dirt.
Just be mindful of that,
especially from the maintenance perspective, because
we do see a lot of these slip clutches
that ended up freezing up because they
get rusted in place.
Running through those maintenance procedures on
the slip clutches and you're pushing your tillers like this,
certainly is a good idea.
That's a little bit on rototillers, their use,
operation, maintenance and features.
If you're going through the buying process
on a piece of equipment like this and you're considering a rototiller,
it's definitely one that you want to consider picking up. For us,
it is probably our second most popular
implement after a front loader
and that's because so many of our customers
do their own gardens and those kinds
of things around their property.
It is also a piece that we rent.
You notice I told you here, this is our rental tractor
and tiller that I'm running here today.
Renting these things is a nice thing
because it is something that a lot of guys
are only going to use once a year.
It is an option if you're local
to us to be able to do that kind of thing as opposed
to owning one of these and having it on your property
year-round for the occasional use you might have with it.
If you're in the market for any attachments
or if you have parts or service needs for equipment
you've already got, give us a call at Messick's.
We're available at 800-222-3373
or online at messicks.com.
[music]