In this video we'll provide a few tips on Circuit breaker selection. The proper sizing
of these devices is ultimately your responsibility, of course, but hopefully these tips will help
point you in the right direction. Circuit Breakers and fuses provide similar
function but circuit breakers can be much more sensitive to faults. Circuit Breakers
can make it easy to identify where the fault is -- you can see the switch is tripped, with
a fuse you have to disconnect it and test it if it doesn't have some kind of indicator
built in. Circuit Breakers allow you to quickly restore
power -- just flip the switch. With a fuse, you have to replace the device every time.
Circuit Breakers have more safety options, things like shunt trips, alarm switches, under
voltage releases, stuff like that. The down side of circuit breakers? They cost
more to install, but over the life time they can actually be cheaper if you take into account,
the man hours spent trying to figure out which fuse blew, equipment lost because it wasn't
protected from things like under voltage and the cost of the replacement fuses and more
importantly the time spent finding/ordering/and replacing them. And of course, with circuit
breakers, you don't have to worry that somebody put the right size and kind of fuse back in
the circuit ... Sizing a circuit breaker for use with a motor
is easy. In the US, you just go to table 430-152 of the National Electrical Code and just look
up the answer. For motors, you want to use this Inverse Time Breaker column which says
size the breaker at 250% of the motors full load amperage. This Instantaneous column is
for high in-rush loads -- you wouldn't want to use that with a motor -- it would allow
the motor to run at 800% of capacity indefinitely. If you are using a fuse on a motor you would
want to use this column for the same reason. MCB stands for "Miniature Circuit Breaker"
and its used in low amperage applications on branch circuits in the under tens of amps
range -- looks like AutomationDirect's MCBs currently go up to 40 amps for example.
MCCB stands for "Molded Case Circuit Breaker". These can handle over ten times that amount
of current and are designed specifically to meet the requirements for feeder circuit protection.
So if you need to protect a feeder circuit or you have a need for a large amperage branch
circuit, you'll want to get a MCCB type breaker. Looks like the AutomationDirect MCCBs currently
go up to 800 amps. The UL rating depends on your requirements.
489 devices are specifically designed for and are rated to protect branch circuits including:
conductors, control panels, switchboards, and motor control centers, things like that.
The 1077 devices are strictly supplemental and should only be used where branch circuit
protection is already provided and you just want extra protection or where protection
it is not required but you want to add some anyway.
The 489 devices can handle up to 100,000 amps of interrupt capacity. The 1077 devices are
in the 10's of thousands of amp interrupt capacity, depending on what voltage you are
using them at. Circuit breakers are rated using a curve type.
A B-Curve Circuit Breaker can handle 3-5 times the rated current before it trips. They're
great for small switch mode power supplies where you need to be able to handle the in-rush
current, but need to be in the couple of amp range while operating. The C curve has a trip
point of 5 to 10 times the rated current -- these are general purpose and are great for small
transformers, and pilot devices. The D type curve trips at 10 to 20 times the rated current.
These are used for transformers or high inductive loads like motors that need time to get past
the high inrush current without the circuit breaker tripping.
Be careful follow the wiring notes in the specs. There's a separate tech tip video on
wiring, but just know that it's really important to follow the wiring guidelines in the spec
sheets and that are printed on the terminals themselves. For example, this one shows you
how many wires and how many strands in each wire are allowed for each terminal type and
temperature range. Also note that they recommend re-tightening
these terminal screws periodically, so consider adding that to part of your regular maintenance
schedule. If you don't pay attention to wiring specs
bad things happen, so please pay attention to those and check out the that tech tip video
on wiring. Sometimes you need to turn off power before
opening a cabinet door -- and sometimes it is a requirement. Circuit breakers have two
ways of doing that. One is this rotary handle, which mounts so that when the door closes
the handle mates up with the circuit breaker adapter directly like this, or using an extension
shaft like this one. In both cases there is an adapter plate that transfers that action
to flipping the breaker switch. The other way, is using a flexible handle
like this. These work with a cabinet that is specially pre-drilled for mounting the
handle so it can work in concert with the door latching mechanism. The nice thing about
this is you have more flexibility on where you put your circuit breaker in the cabinet.
These come with lots of hardware and have built in adjustments so you can mount them
to a variety of breakers. The other nice thing about these guys is you
don't have to worry about drilling a hole in exactly the right place to mate up with
the circuit breaker. Both of these remote handles give you one
other advantage -- they make it easier to flip the breaker switch so you don't have
to get a pair of vice grip pliers just to reset the breaker -- especially on large breakers.
Note that some of these are referred to as "Defeatable.' Normally the switch won't allow
you to open the cabinet until the power is off. There are times though when it is necessary
to access the cabinet while the power is on -- maybe you need to do some diagnostics or
some testing. In that case these are designed so you can bypass or "defeat" the normal operation
of the switch. On this one, you stick a screw driver in here and twist and it releases the
catch so you can open the door. Beware that YOU are responsible for any liability if you
defeat the operation of one of these devices and it's assumed that you are fully aware
of the OSHA requirements for things like arc-flash and the personal protective equipment, etc.
Sometimes you'll want to safely trip a breaker remotely. That's what a shunt trip is for.
It's basically a cheap way to provide remote or emergency shutdowns or even just a way
to automatically shed loads. Here's an example of an MCB Shunt trip. You attach it to the
breaker and then you wire it to a PLC output or even just a manual switch like I have here.
Now you can remotely trip the breaker without opening the cabinet. Once tripped, this device
typically disconnects itself electrically so there is no current flowing through the
control wires. You have to manually reset the breaker after it has been tripped.
An Under Voltage Release - or UVR - trips a breaker when it senses the line voltage
is too low. This is handy when you have a system that shuts down and you want to be
sure the system isn't heavily loaded when it tries to start back up. The UVR will have
tripped the breaker when the line voltage dropped so when you go to bring the system
back up, this load won't be a burden. Here is an example of a UVR for a MCCB. These are
typically mounted inside the breaker here. Once the line voltage is back up, you then
go and manually reset the breaker. An Aux contact gives the PLC a way to monitor
the status of the breaker. Here is an example of an MCB aux contact. It just clips on here,
so when the breaker trips, the contact closes. Can you stack these MCB style accessories?
It depends on the vendor, but usually the answer is yes. For example, here is a shunt
trip and an aux contact stacked on a three pole breaker. Now we can remotely trip the
breaker AND monitor its status. This aux contact is a little different because
can detect if the breaker was tripped manually or electrically. This set of contacts tells
you if it tripped electrically, and this set tells you it was tripped by either. Connect
those to PLC inputs, and now the PLC can tell what caused the breaker to trip - a fault
or a co-worker. If I rotate this little switch right here, now both sets of contacts trip
on either manual or electrical faults. Cool. Three are a number of other accessories that
can tell you if the breaker tripped due to Overload, Phase loss or short circuit etc.
The point here is there are lots of ways circuit breakers and their accessories can help you
quickly diagnose problems in your system, so check 'em out -- they can save you a lot
of time, money and headaches in the long run. With so many circuit breaker options and accessories,
selecting the one you need may seem overwhelming. Fortunately, the AutomationDirect Website
makes it easy. Just select Circuit Protection, and if you want a miniature circuit breaker
or a larger MCCB. We'll choose the MCCBs. Now we can specify do we want everything or
just the circuit breakers or just the accessory's -- let's select circuit breakers. Now we just
choose the voltage we need to operate at, and the number of amps we need. And just like
that I'm down the exact part number I need. For accessories, I can click on that part
number and scroll down to the bottom and there's a bunch of suggested accessories that could
go with that breaker. The other way to do it is to come back over
here select MCCB, and this time choose accessories, and I can select the component type I want,
let's do a shunt trip for example, and select the type of breaker I am using let's assume
we selected a Fuji, and all of the sudden, we're down to four possible part numbers which
we simply match up with the series of breaker that we are using -- in this case a 250 or
a 630 and whether we want 24volt or 120volt AC controlled. This parametric search makes
selecting circuit breakers and accessories so easy.
That ought to be enough to get you going with circuit breakers. As always, if you have any
questions, please call Automation Directs free award winning technical support during
regular business hours. They will be happy to help you out.
And don't forget the forums -- there are lots of folks there that love to share their years
of experience. Just don't post and support questions there -- Automation Directs tech
support team may not see them.