I got to do my stuff there cross
all right so here's a good example of what I was talking about earlier we've
gone and we've made sure that our Eve was straight but in between the truss
tails you've got an eight-foot space and the lumber can get a little wavy so what
we always try to do is have an inch and a half reveal on our roof now if I come
in here back at the lab I'm at inch and a half and there's a trust right here so
I know I'm good but if I come out here I'm in the middle of this Bay my steel
is reading inch and five-eighths so what I do is I want that to be inch and a
half so I'm gonna tell Greg at the top pull it back what he's gonna do is he's
gonna pull that steel back right there Greg wait bring it ahead so right now
I'm at an inch and a half I go ahead and
I go ahead and set my screw now what that's doing is I've already assured
that my string line is straight on all my tails so by doing this by moving the
steel so that I'm an inch and a half off my fascia board once I screw it all off
I will be consistently an inch and a half and when I go through my tails I
should be at my inch and a half which means it's going to straighten out all
of those ins and outs throughout the roof so that's the goal it doesn't
always happen perfectly we'll see we'll run the rest of this
roof and see how it turns out
so this sheet here you look up in the roof
we've got about 21 inches up at the top so we laid it out so that this would all
work out according to plan so what I've got to do is I'm gonna first rip this
down this is our 21 inches but I'm also going to leave myself three quarters of
an inch and I'll use my roller vendors that they're sitting there and I'll roll
up a three quarter inch flip on the edge that is just in case any water gets over
this rib and you'll see it when we get it up there I'll show you how this works
twenty-one inch mark begins
you guys have probably seen us use these we use them a lot out that Jimmy dress
to build we've randomly used them these are versa vendors and steel dynamics
that doesn't sound right dynamic fasteners is where I bought
these and what these are going to do is you can adjust them all sorts of
different ways we've got them set up for a three-quarter inch
Bend up and the way these things work is they just create a little crease now if
you can zoom in there I don't know if you can see that Greg all I'm doing is
I'm just barely putting a slight Bend on this I'm gonna be able to go all the way
but that's okay
now what I do is I start to give it a little bit more because these rollers
are offset the way they are and the way all these beads work it forces this
piece of steel to want to roll up so I'm not I'm not really doing much I'm just
giving it a slight pull up as I roll back and forth
so now you can kind of see what we've got here I always like to take the hand
vendors and just it's not a hundred percent necessary because this is going
to be buried underneath of our gable trim but now you can see what we got
going on this is that section that goes up high and then this is where the
different transition is on the lower roof section and this whole detail right
here I'll show you guys that in a later video when we actually put our ridge cap
our gable trims our fascia there's a lot that's gonna happen in this spot but
let's go get the sheet up on the roof well there you go just got that sheet up
you can see now what we were talking about we've got that bend up way over
here that protects any water from going into that fascia it's gonna run
everything down and out the steel and our ridge cap will come across here that
detail will come another day because somehow it's already four o'clock and
we've still got a lot of roof to put on I didn't expect this to take this long
and I haven't even been recording much so maybe the cold we're getting old
are you ready born 35 you already know the answer is that little tougher you
man you need my help I got you
so I'm just gonna make sure that this overlap is perfect okay Gregg pull it
back keep going keep going keep going keep going keep going right about there
so I already kind of knew that this Bay there was a little bit of a ninny on the
fascia board so that's why I kind of saved it for the for the video because I
knew that this will hopefully show you guys would be a good teaching point as
what to do because I always get that question about how do I keep my my steel
from having Jags in it okay one side of roof is installed screwed off and
started to find this thing so I like it I love it I'm gonna throw the drone up
in the air and get some more of it