Hi, DIYers.
This is Michael from Alarm Grid.
And welcome to part one of our installing the Qolsys IQ panel
to system.
This applies to a Qolsys IQ panel 2 or a Qolsys IQ panel 2
plus.
So, in this part--
this first part-- we're just going to show you
the basic wiring powering on the system for the first time.
It's very simple.
It's very easy system to use.
So what we're going to do is--
you see that this system comes with the power cable.
This is actually the one that it comes with, right here.
It's got a positive end and a negative end, as you can see.
And then, there's a barrel connector
that's actually going to go right to the back
of the system.
First, what I'm going to show you
is just connecting it to the transformer.
Now, this is a DC transformer so polarity is going to matter.
So you're going to have to make sure that the color wire goes
into each of the proper sides.
So we have our positive side, red for positive.
So we're going to take our red one
and this is also the one with the dash lines.
As you can see, the positive is going
to have the dash lines on it.
This is actually the cable that comes with it.
So you're just going to take it and put it into here.
And then we have our screwdriver over here
and we're just going to screw in.
And we want it to be tight, so it's firm.
But you don't want to make it too tight
because it can cast bronze if you
need to remove anything later.
So let's do the quick tugging.
Looks good.
Now, we have our negative, that's black.
And this is the solid wire.
It's not dashed.
There's no gray dash on it.
So we're going to take it in.
And then secure.
Same as before, just tight but not too tight.
That's good.
Give it a quick tug.
So our transformer is wired in on that end.
Now, what we're going to do-- we have our barrel connector
that's just going to go right into the back of the Qolsys IQ
panel 2 system.
You see, there's a barrel connector right there
at that little black part.
So we're just going to take it and just put it in.
Just like that.
And you'll also see that the system comes with a back plate.
This is just for making it neat and tidy.
Now, you'll see that there is a wire coming out of the system.
Now this is actually the antenna,
for communicating with sensors.
So you want this to be outside the panel.
Otherwise, if you tuck it in somewhere,
that can cause frequency problems later
on-- transmission problems.
So you're going to want to leave it outside.
So what you can do is you can actually just hook it
around that.
So you hook around that loop right there.
And then this can just kind of go
as such you don't need to hook around anything.
And you'll take your back plate.
And you see there's a little indentation
part, that's going to go over the wires there.
So you just kind of slide it in.
Snap it into place.
And you're good to go.
So then you just take your transformer
and you just plug it into a usual outlet.
I actually have one beneath the desk here.
So we're just going to go and plug it in.
And now it's plugged in.
So now we have the system.
And to power it on, what you're going to do?
You're just going to pull down the button down there.
And you have to hold it down for a little bit,
don't just release it right away,
like give it a good moment.
Otherwise, it'll just shut off.
And as you can see when the light is solid, that's enough.
It will take a second for it to power on.
So you can see the green flashing LED,
that's a good sign that it's powered on successfully.
And when you boot this up for the first time,
it's actually going to go to a wizard
to help you install the system.
So we'll get to that in a second.
It does take a minute to boot up.
So we'll just wait for that.
And I almost forgot you might want
to see the table stand for the Qolsys IQ panel 2 system.
It's very simple device here, you just put it on the back.
And this way, you don't have to mount the system to a wall.
You don't have drilling holes.
You can install the entire system with just a screwdriver.
So what we're going to do, you just have it here.
And so it, literally, just goes in there and you push up,
and it sticks into place.
And then you can have this system standing like so.
So then, as you can see, now that we
have the system powered on, we have it at the wizard menu.
This is what you'll see the first time you
turn on the system-- if you are using
this system for the first time.
And this is actually going to help you use the system--
help you set it up for the first time.
If you're new to the system, it will cover
everything you need to know.
But we'll get into that into the second part.
So if you did enjoyed this video,
please click the thumbs up button below
to like this video.
And you can click the bell icon to subscribe to our channel,
if you want to get updates on future videos.
And if you have any questions, you
can email us at support@alarmgrid.com.
We hope you enjoyed the video.
Thanks