welcome the following video will demonstrate how to program a 2gig
takeover module into a 2gig gc2 annal the takeover module contains eight
terminal inputs which allow you to convert eight zones from wired to
wireless each of the eight inputs should be programmed to separate zones on the
panel to program one of the takeover modules inputs into a security zone you
will first need to access the installer toolbox press the 2gig logo on your gc2
panel's screen enter the installer code the default installer code for the GC 2
is 1 5 6 1 you are now in the installer toolbox to access zone programming press
system configuration you'll see q1 select RF sensor number displayed in the
upper ribbon of the screen system configuration is navigated via questions
and sub questions wireless zones are programmed in q1 so we are already on
the correct question for wireless devices first you will decide which zone
number to assign to the takeover module input you are currently programming note
the word sensor and zone are interchangeable in this training we will
use the term zone number by default we are already on the correct sub-question
to select the zone number the white field is called the answer box 0 1 will
display in the answer box by default which means we have selected zone number
1 if you would like to change the zone number press the right arrow to change
the zone number or type the desired number in using the number keys on
screen you will see the new selection appear in the answer box once the
desired zone number displays in the answer box press the down arrow to go to
the next sub question select the sensor type there are two
ways to change the sensor type option one press the right arrow to scroll
through the various sensor types option to use the on-screen keypad to type in
the two digit code for the desired sensor type select the sensor type that
corresponds to the hardwired device you are converting for example choose zero
one exit entry one if you are converting a hardwired door contact
press the down arrow to go to the next sub question select the equipment code
press the right arrow until to Gig takeover module displays in the answer
box you can also type 0 8 7 3 to select this option press the down arrow to go
to the next sub question next input the serial number for the takeover module
you will find the serial number inside the takeover module the serial number
will contain seven digits and end with 1 use the on-screen keypad to type the
first six digits of the serial number then type the input number you are
currently programming in this example we are programming input 2 on the takeover
module so we will type 0 2 0 3 0 9 which are the first six digits of the serial
number and then 2 which is the input number press the down arrow to go to the
next sub question select the equipment age it is recommended to program input
terminal 1 is new and input terminals 2 through 8 as existing press the down
arrow to go to the next sub question next select the loop number the takeover
module uses loop number 1 so we can leave a default option as is press the
down arrow to go to the next sub question choose whether to enable or
disable the dialer delay the dialer delay is used to prevent false alarms to
enable the dial delay use the right arrow to select
option one to disable the dialer delay leave option 0 disabled press the down
arrow to go to the next sub question next add the voice descriptors press
insert the word abort will automatically appear in the answer box change the word
by either using the right and left arrow buttons or by typing the words three
digit code using the keyboard for a list of all voice descriptors and their
associated codes see the installation and programming guide to add another
word press insert again and repeat the steps just discussed you can add up to
five words once the desired word or words displays in the answer box press
the down arrow to go to the next sub question next choose whether or not to
send reports to the central monitoring station if you would like reports
related to the takeover module to be sent to the central station select one
enabled press the down arrow to go to the next sub question next decide
whether or not you want the panel to monitor supervisory signals of the
takeover module such as low-battery tamper and more select one enable to
activate this feature press the down arrow to go to the next sub question
lastly the panel can be made to annunciate sensor names by selecting a
chime use the right arrow to scroll through the list of chime options once
the desired option displays in the answer box press the down arrow to go to
the summary page review the summary page to ensure all information is correct
review all answers if you need to edit any of the information press edit
current to exit programming mode and save your changes press skip then press
end the option to save changes is selected by default finally press exit
the system will automatically save the new information and the panel will
reboot the 2gig takeover module is now programmed into the 2gig gc2 panel make
sure to subscribe to our YouTube page and click the show more tab underneath
the video where you can view valuable links pertaining to this product similar
how-to videos and our low-cost no contract alarm monitoring services