1. Unscrew the brake fluid reservoir cap.
Required tools: Wire brush WD-40 spray
Brake cleaner Multipurpose grease Copper grease
Combination spanner №15 Drive socket # 13 Drive socket # E16
Drive socket # 30 Wheel impact socket #19 Ratchet wrench
Torque wrench Brake caliper wind back tool Tap wrench
Hammer Rubber mallet
Crow bar Wheel chock
2. Raise the rear of the car and secure on supports.
3. Unscrew the wheel bolts. Use wheel impact socket #19.
AUTODOC recommends: To avoid injury, hold up the wheel when unscrewing the bolts.
4. Spread the brake pads. Use a crowbar.
5. Clean the brake caliper fasteners. Use a wire brush. Use WD-40 spray.
6. Unscrew the brake caliper fastening. Use a combination spanner #15.
Use a drive socket #13. Use a ratchet wrench.
7. Remove the brake caliper.
AUTODOC recommends: Tie the caliper to the suspension or to the body
with a wire without disconnecting from the brake hose to prevent depressurization of the brake system.
Make sure that the brake caliper is not hanging on the brake hose.
Don't press the brake pedal after the brake caliper has been removed. As a result,
the piston can fall out from the brake cylinder, and brake fluid leakage and depressurization of the system may occur.
8. Remove the brake pads. Use a crowbar.
9. Clean the brake caliper bracket fasteners. Use WD-40 spray.
10. Unscrew the caliper bracket fastening. Use a drive socket #E16. Use a tap wrench.
11. Remove the caliper bracket.
12. Pry up and remove the wheel hub cap. Use a crowbar. Use a hammer.
13. Unscrew the hub lock nut. Use a drive socket #30. Use a tap wrench.
14. Remove the brake disc assemled with the wheel hub bearing.
15. Install the brake disc assembled with the wheel hub bearing.
16. Screw the wheel hub lock nut. Use a drive socket #30.
Use a torque wrench. Tighten it to 105 Nm torque.
17. Treat the hub where it contacts the brake disk. Use a multipurpose grease.
18. Install the cap of the hub nut. Use a rubber mallet.
AUTODOC recommends: The cap must always be replaced. When you install the previously used cap the sealing will be lost.
19. Clean the brake caliper bracket from dirt and dust.
Use a wire brush. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
20. Install the brake caliper bracket
21. Tighten the brake caliper bracket Use a drive socket #Е16.
Use a torque wrench. Tighten it to 85 Nm torque.
22. Press in the brake caliper piston. Use brake caliper wind back tool.
23. Install the brake pads.
24. Install the brake caliper and fix it. Use a combination spanner #15.
Use a drive socket #13. Use a torque wrench.
Tighten it to 35 Nm torque.
AUTODOC recommends: Without starting the engine, press the brake pedal several times until you feel significant resistance.
25. Treat the surface where the brake disc contacts the wheel rim. Use copper grease.
26. Clean the brake disk surface. Use a wire brush. Use a brake cleaner.
AUTODOC recommends: After applying the spray, wait a few minutes.
27. Screw in the wheel bolts. Use wheel impact socket #19.
AUTODOC recommends: To avoid injury, hold up the wheel when screwing in the fastening bolts.
28. Lower the car and working in a cross order, tighten the wheel bolts.
Use a torque wrench. Tighten it to 120 Nm torque.
AUTODOC recommends: Check the brake fluid level in the expansion tank and refill if necessary.
29. Tighten the brake fluid reservoir cap.