hello and welcome to this video where
I'll be showing you how to install the
Whitestone dome glass screen protector
to the Samsung Galaxy S 10 plus we'll
also be testing it out to see how well
the phone performs with the screen
protector installed please don't check
you don't already have a screen
protector applied as Samsung's new
release does come with this straight out
of the box if you do have one on just
simply peel it away to begin with lay
out all of the installation tools and
keep them close to hand as there are
quite a few steps in comparison to other
screen protectors once you have
everything set out take a couple of
moments to check your work areas
completely flat as even the slightest
incline can cause the adhesive liquid to
slide off the phone during the
installation process a quick and easy
way to check this is to place one of the
adhesive bottles down and see if it
rolls if it stays put then you're good
to go but if you find it rolls you'll
need to find a level surface before you
begin with your s 10 plus place on a
flat surface take one of the alcohol
wipes and thoroughly clean the entire
display and the edges of the phone next
use the microfiber cloth to dry the
screen before using the dust removal
stickers to dab away like so this will
lift any final dust or lint that can be
annoying if caught under the screen
protector during the installation you
can now place your phone into the bottom
section of the installation tray making
sure you match up the speaker to the
speaker text of the tray with that done
you can go ahead and cover the speaker
with one of the protective stickers this
will ensure that no adhesive can get
into this part of the phone now you can
go ahead and fit the top section of the
tray matching up the speaker text to the
text of the bottom tray Whitestone also
provides you with two absorption pads
for you to place either side of your
phone these pads will help take care of
the adhesive gel once it spills out from
underneath the applied protector at this
point I would advise given the screen of
final chat with the dust removal
stickers just to double-check that the
screen is well prepared and ready for
the protector to be applied next take
the plastic pin and insert it into the
gap like so before position in the
bridge into the area's shown at the top
section of the tray you can now turn
your
to the bottle of adhesive and remove the
larger colored card do take care to
remove this cap first as the second cup
controls the release of the adhesive
begin to screw the bottle into the
bridge like so don't worry about any
spillage as no liquid can be released
until you remove the second cap with the
bottle secured remove the second cap and
allow the adhesive to run onto the
display for around 30 to 40 seconds this
will make sure all of the liquid is air
and on to the phone once the adhesive is
completely out slowly lift the bridge
and the adhesive bottle from the tray
taking care not to move the adhesive
bubble you can now turn your attention
to the screen protector itself begin
peeling back the protective film taking
care not to touch this side with your
fingers lower the protector into place
starting with the bottom first before
resting the top on the guide pin that
was slotted in earlier once you're happy
with the position press down on the
bottom of the tray to slide the adhesive
bubble to the center of the S tens
display when it reaches this point
removed the plastic pin and stop
pressing on the bottom of the tray
this action will cause the protector to
fall into place and allow the adhesive
to spread throughout the entirety of the
screen you will need to allow a couple
of minutes for the adhesive to spread
correctly but you'll be able to see when
it's completed anyway now you can begin
the primary curing process take the UV
light and position at the top of your
rest m+ for 15 seconds before repeating
this process at the bottom for a further
15 seconds following this lift the top
tray and remove the s10 plus now you can
use the leftover alcohol wipe to remove
any of the remaining a.dc from the edges
place your rest m+ onto a clean surface
and use the UV light for the secondary
curing process you should leave the
light to each end for 60 seconds this
will complete the installation process
allowing you to enjoy your rest m+ with
the peace of mind that the screen will
be protected as with all white stone
screen protectors you'll instantly
notice a superb fit look and feel - any
horrid glue marks that can often be seen
with other protects
you also notice the crystal-clear
appearance which looks fantastic
many of the screen protectors tend to
use a black lining around the edges to
hide the glue whereas the dome bus
doesn't need to do this thanks to the
high-tech installation process with the
protector applied the s Templar stays
just as responsive as before meaning you
can use your phone as you would normally
including typing with flawless accuracy
as well as using the fingerprint reader
with no issues white stone do recommend
to re register your fingerprint after
installing their screen protector to
make sure that the s templates can get a
precise reading every time this is
supremely clear with just as much
clarity as before which makes watching
videos and playing games a truly
enjoyable experience while installing
this protector may seem like a hassle I
genuinely found it extremely easy by
following the steps in this video you'll
be guaranteed of a well applied screen
protector that's easily the best
available on the market today it is a
little expensive when compared to other
screen protectors but the unique
installation method really does ensure
the quality fit that's like no other
that's all we have for our installation
and review if you have any questions
then please do leave them in the
comments below for more information also
even purchase this screen protector for
your s templars i'll leave a link in the
description and comments of this video
[Music]