hello I'm Scott Brown with green wind and other homeowners well a few days ago it rained finally
after close to about three months and we finally got some wind back here this got
caught out in the rain rusted up at all looked like the inside I put it on a clamp and got the
belt sander after and got the edges real good now we're ready to go ahead and put the magnets
on this one and cast it as well well hopefully we get to watch it for and show you how that
little process works okay well there's the other side of it all cleaned up nicely that's beautiful
little patterns in it stay out of plight two different angles on it here we go that's all
nice and cleaned up I think I'm going to paint this side first with some epoxy oh yeah that's
beautiful one hand on the crank one hand on the spray can some anti rust spray enamel beautiful
kind of pretty heated alright remember that going the magnet up in the air it's gonna I
turn it on this side here it's going to do a little flipping put it on this side it kind of
stays in the same spot comes down the same way this is the south side of the magnet let's just
that theory all right this should be the south side of the magnet which means with this side
facing out it should repel on that middle one yup it repels hold that one oh yeah that's the
south side right there and we got it right okay well I've got the three little notches right here
I've got my template set up I've got it all the way to here but you'll notice it's got a little
bit of a slop in here well that's because this rotor is just a wee bit bigger soon as I like
I said I get everything free if I can the main deal is I make there I got an equal space over
here an equal space over here so this is perfectly straight because this is going to set up all the
other magnets so first off I'm not even going to use superglue on this first one I'm going to
set this one up it snapped in make sure it's all the way out to the edge next one I'm going to do
over here I'm going to use another South magnet because it's south north south north south north
south again and I'm going to make sure this is lined up dead center oops I really don't want
to be touching the rotor too much alright we're going to do that might as well show
you how to pull a magnet off over here remove the stand rather than going for another take
anyway the way they normally tell you to do is the push down get your hand right on the edge
and push down and I'll tell you what this piece will want to come out I'm going to go ahead and
let it do that because it seems to getting away from me there we go get out of here pushing down
off the edge of the desk really gets hard I turn them sideways then I push them down and
I'm going to come over here and I'm going to use my thumb as well as pulling and pushing and then
while I got it here I'm going to pry it out get my finger underneath and then I'm going to roll
this one off of here cuz these things I've tried it the other way and it's just really hard to do
but anyway I've got this one off let's put it on the rotor alright first thing I want to do test
to see if it's pulling if it's pulling then it means it's going to its lamé the same polarity
as the other one I'm going to go all the way to the other side double check to make sure my
spacing is right on each side and that's where that one's going to go doing this backwards kind
of I want to get right make sure that template does not move and now we're inside that lip it's
not moving double-check my spaces I could use just a touch now this will go back and forth
turn this over here get at least one of the North magnets set in here all right I've got the disc
turned I've got this centered from this side and this side I'm double checking it because you see
it'll slide back and forth Center it from both sides here stick it over here now this really
ain't going to move I'm going to do the other side that ought to pin them all look a little of
the paint stuck more magnet alright : repelling it's pulling rappelling repelling that's right
and everything is still lined up not to worry too much because I can still move them I haven't glued
any of them down we'll get this thing lined up perfect make sure all these are out to the outer
edge as far as they will go look at the gap all the way around it seems to be perfect look this
will not move anymore now we're going to put all the rest of the magnets out you've seen it on the
last video so I don't have to do that on camera okay and for the finale of doing this always take
your last magnet nose it pulls here well it's on the wrong side it's repelling it's pulling repel
pull repel pull repel pull repel the pull repel and this one's repelling you know this is where
this is supposed to go and the last one is n okay I've got some of this drywall tape and I ripped
it into little strips like this I want to round this twice and this is basically nothing really
needed you know you'd have to get over a thousand rpm and for a 10-foot prop I really don't think
it's going to get there especially when it firls at about 30 miles per hour but right up here you
look right there broke off and right there figure this just might help on here so we're going to
ahead and throw that on there anyway this F inch lip right here is going to keep them magnet from
sliding out I've already super glued all these things and about ready to go ahead and put the
aluminum foil tape I got some taller aluminum foil tape where I can just lay it on the table
and pull it around and that's going to make this a lot easier well I went ahead and put all the
super glue around the edge of all these magnets all the way around and I super glued the fabric
the fiberglass fabric on all edges on the outside my super glue was kind of hardened up in the end
I guess the heat got to it so I took a little wire that I sharpened and I poked a hole in the
very bottom edge I had no problem hanging on to the tube of superglue problem was letting go okay
so I've got the I've got the inside done already laid it flat on that edge had a curl inside pushed
her around she came out real nice and I got the outside piece measured this is basically how it's
going to go on so it'll be in nice and tall and sit there wonderfully and you missed it on the
last video because I had it out of frame but this is the basic way to peel this without having to
curl and give you a whole bunch of problems this is the paper the other part of the tape keeping
it down like this keeps it from curling up grab it by the glue pick her up set her down I've got
it in a curl push it to it keep everything flat if I keep this level with the table I can just
walk right around this I try to keep it leaning back go I had a flat flatter surface this would
work out a lot better just pull the tight smack these together and that's pretty good she's
ready to pour cording to the directions on the fiberglass resin or the polyester resin it says
ten drops per ounce okay well how to measure that Dave 972 Oh two told me it's 15 drops four cubic
centimeter I have four cubic centimeters here that is 60 drops I have seven ounces of resin
I want there harden a little slower than ten minutes so basically I've decreased it by ten
drops I've mixed baby powder with it this time so we're going to mix all this up I've already beat
all the little lumps and white little things out of here I guess it's okay to add the hardener now
dump all of it in it once there we go and we're get it good mix when fiberglass resin hardens
fast the only problem with that is it becomes brittle and it shrinks the stuff is guaranteed
not to shrink maybe I've missed measured last time but I think I got it real close but took
safeguards against all of that and hit basically you didn't get to see all of this last time what I
do is work between the magnet wait'll it starts flowing around go to the next one the next one
and the next one and I got this on the level spot of the table as you seen in my last video
I know I left it up there a few weeks before I got around to doing any more just enough here to
come up halfway up the magnets last time I used a little bit more than I wanted to here we are
while we're off camera before I put the aluminum foil tape around the outside as the mold I went
and cleaned everything up with acetone because it's a zero residue cleaner I didn't put a lot
of baby powder in this time I just don't like that pink effect slop this over the sides over
the edges over here got plenty of time I used used a little less harder so it'll last a lot
longer this way shouldn't be brittle I think that's what happened on the other one I take
some up on top of the magnet after i coat the top of the magnet coating the magnet some people say
you shouldn't do but some people say you should do diamond mine boring is very unstable and you
think about it with the strength of these magnets and every molecule inside of it is trying to repel
itself I imagine it would corrode rather fast and get some over the edge or here on every one
of these magnets on the outside go once you've coated all the surfaces you can let it all sit
and level out make sure you got every little edge this outside edge here where I've got
extra tape I'm going to wind up trimming that with a razor blade I believe everything looks
perfectly even wonderful ready to go let her sit this is what you missed on the last video nothing
really fantastic double-check it around this to make sure all the level moving fiberglass are
the same height like it could go it's stuck oh there you go slide this a little bit that
way think after the last rain the low spot my desk has changed I want this only to come up
so far on the magnets as I want it to move air across the stator and help keep it cool
plus it'll help keep the magnets okay well we're gonna finish up here yeah everything seems to be
hunky-dory this aluminum foil tape it sticks real hard and the glue likes to come off but
if you peel slow give the glue time to react this didn't get real hot this time you pull
real slow this giving this glue time to react it won't be pulling the paint off my rotor boom
this stuff sticks to anything I put some on a wood stove I had in Virginia one time where the
tube where the plates came together like this after about two years I have of that wood stove
not one time did I even had it blowing red not one time did I smell smoke in my house and that stuff
actually stuck to it and kept sticking I swear this stuff sticks to everything we are coming
out real nice all right I'll pull on this side so y'all get a little view look I took one small
piece of paint still add some under it though that's okay get this to curl out there we go
whee-ha this is coming out wonderful I'm liking this a little faster I'm
not gonna worry about it I'm gonna give it more pain anyway time to turn this oh
yeah so we stopped sticking the things there we go that's a [ __ ] it cleared the desk off they used
to use this aluminum foil tape on long pieces of bamboo use some tie wraps not to eat antennas that
I talked around the world on an antenna farm like you would not believe there's plenty of bamboo
cheap this little antenna you can come up with you want a three element yogi beans yeah one roll of
this we'll get you some bamboo and tie wraps measure cut it with a razor blade when you're
done everything comes out wonderful believe that stays on fiberglass basically get that off with
alcohol I think we're done here looks beautiful it's still a little soft that's good it's not
going to be brittle this time 60 drops for seven ounces little bit of baby powder a fully casted
magnet rotor I'm Scott Brown with green wind and other home energies many good things to
you and yours thank you for watching I appreciate everyone in the end comment and the help god bless
you