Whether you’re building an arcade or some other contraption the goto board for most
of these projects has been the Raspberry Pi series of single board computers.
Since the Raspberry Pi runs an ARM Cortex processor, you would normally run Raspbian
- which is a Linux based operating system.
If you want to run Windows, you're stuck with Windows 10 IoT or Internet of Things.
This can be less than desirable because Windows 10 IoT will not run most desktop applications
and can be very limited in functionality.
Well now there’s a single board computer running an Intel Atom processor that comes
pre-loaded with a full copy of Windows 10.
It has x86 GPIO and even includes an integrated Arduino.
Let me introduce you to the LattePanda!
Now many of you over the years have asked me if there is a Windows based computer that
you can use in my arcade projects and other projects.
And the answer has been “Sure!
Just go ahead and build any Windows based PC and put it into your arcade.
Well unfortunately when building a bartop arcade or some of my smaller projects a full-size
PC isn’t really optimal and may not even fit.
Well the good news is they guys over at DFRobot have been listening to us and they have come
up with this single board computer that is slightly larger than a Raspberry Pi and runs
a full version of Windows 10.
In fact it comes pre-loaded from the factory with Windows 10 and this is perfect for smaller
projects like bartop arcade cabinets.
So let’s take a look at it!
The LattePanda comes boxed in some pretty nice packaging.
As you can see I purchased the enhanced version that has 4GB RAM and 64GB of flash storage.
There is a cheaper version that comes with 2GB RAM and 32GB of flash if your looking
to save a little money.
Besides the LattePanda itself, you’ll also find a wireless antenna in the box that can
be remote mounted for better reception.
Of course, you can certainly install a 3rd party antenna if you prefer.
Let's start the tour of the LattePanda on the side with the USB ports.
On this side you will find an HDMI 1.4a port, a single USB 3 high speed port, and two USB
2.0 ports.
I really like this configuration because it gives you USB ports for a mouse and keyboard,
and leaves your USB 3 port open for peripherals such as external storage devices.
The HDMI port is capable of 4K resolution, but only at 30 frames per second.
Turning the LattePanda counter-clockwise you'll find a reset button for the Arduino chip along
with the Arduino header which is where you would connect devices and breadboards for
your projects.
In addition to supporting a full Arduino you will also find a smaller header which contains
GPIO directly from the processor.
This opens a world of options for controlling external devices.
If you were using this for an Arcade for example you could use the GPIO to activate and flash
lights or run cabinet shakers.
Additionally on this side you will find the power and reset buttons.
On the next side of the LattePanda you will find a 100 megabit Ethernet port, a 3.5 mm
audio jack for connecting speakers or headphones, a micro-SD card slot for supporting additional
storage, and a micro-USB connector for input power.
The LattePanda requires a 5 volt 2 amp input minimum.
If you're going to run additional accessories I would recommend going for a 2.5 amp supply.
Most of your fast charging cell phone adapters will meet this requirement.
On the last side of the Latte Panda you will find the screen connectors for LattePanda's
7 inch IPS display, and a connector for the touch screen overlay.
This can be fantastic for adding a small display to some Internet of Things project.
Here is something interesting about the LattePanda.
They provide some of the Arduino inputs in a second form factor called Plug and Play
Sensors Connectors.
They sell an array of temperature, humidity, motion sensors, and other sensors that can
easily be plugged into these connectors.
They've basically idiot proofed them for use in schools and learning environments.
Some other things to note about the LattePanda are the inclusion of a Realtek wireless chip
that offers BlueTooth 4.0 and 802.11n Wi-Fi for wireless connectivity.
I was also quite surprised to learn that the CPU is actually located on the bottom of the
device, rather than the top side.
This causes some issues with venting the processor which we will see in just a minute.
The case sold by DFRobot is made from laser cut acrylic that comes on these sheets.
You'll need to pop out all of the pieces from the larger sheets in order to build the case.
It took me quite some time to remove the adhesive paper layers from all of the components.
Now I have to tell you, assembling the LattePanda case is like a Chinese puzzle.
Putting one part in causes another part to fall off.
But once you get everything lined up it goes together pretty easily.
I really recommend waiting until you've built the case before installing the board.
This will allow you to precisely mount the CPU fan on the bottom of the case and everything
will align much easier.
So let’s talk about a few more things surrounding the LattePanda.
So one thing I want to mention that I really find to be a flaw with the design of this
is that the processor is on the bottom and the fan is also on the bottom, which means
when you set the LattePanda down on a desk or surface the fan is almost obstructed.
So if you were to set this thing down on anything like a towel for fabric or anything like that
it would block the fan flow, er air flow from the fan and so I really don’t like that
design.
Now here’s the good news.
If you’re putting this in something like an arcade cabinet, the case is really 100%
optional.
There is no reason to really have it all.
Just put some standoffs in your cabinet and just mount the LattePanda directly to that.
The other thing I want to mention is that if you’re going to use the LattePanda for
something like an arcade there is some really awesome software out there that you should
checkout.
It’s called RetreoArch.
And that is actually what the Raspberry Pie version RetroPie is originally based on is
RetroArch.
So it can emulate all of the same video game consoles and arcades that the RetroPie installation
can emulate only all on Windows.
And so I highly recommend that you go check that out.
Well hey guys!
Thanks so much for watching!
I’m going to play a little pac-man running on the LattePanda.