the Anatol titan is coming together nicely stick around to see how far we got the plan
today is I'm going to move both of these crates out and then remove the base into
place where the old press was that so it's going to be a lot of work I got
a lot of organizing to do here in the shop because it's quite the mess and
we're here on a Saturday needing to get some stuff done so let's get after this
well I'm hung up on the edge so I think what I'm going to do is take some of these squeegees off
get a little bit of the weight off perhaps take the station arms off see if that lightens it up
a little bit take the pallets out from this side it's that way I can continue to move this thing
forward so I'm pretty sure those pallets have some good weight to them we'll get it outside
and get these heads outside it's quite the project it's we'll find out what that is later
there no
looks like a Inman are styled racket so if that's the case I won't have
to orders me Palace because I have one well I got all of the arms out I
wasn't too terrible now I just need to get this thing further that way
well the bass is all tore down Trading's tore down to the base you'll have to excuse the window
waiting for my power drill to recharge and then I'm going to take this board off right
here it's that way I can slide the pallet jack a little further up underneath the press
and that should help me pushing this thing back getting that bad boy out of there and
we can slide this one on in and put it into place I got that final board off now should
be able to slide the forklift underneath it or the pallet dolly underneath it and
hopefully and slide this thing up all right now it's time to move the heads I
guess we'll see how difficult it is to move right Apollo follows checking out the press
got the the heads out of the way now let's try and move that thing in we're
gonna Park it right over there and then who knows maybe I'll assemble it myself
after pushing and pulling she acting things up counters finagling things
she's inside I smashed my toe in the process I didn't show good
okay it is in place now I just have to rotate it she's in her final place for
now I might have to just a few inches here and there but I took some measurements all
around put the dryer in place and I think it'll be good there and the
kids are out there with their lemonade or ice cream truck having a good time
the crate of heads is finally back in and this has been exhausting I would definitely recommend
renting a forklift that would have made it a lot easier but here I am Saturday with the kiddos at
the shop just trying to get this thing as close to being ready I guess really just trying to
minimize the amount of work that needs to be done when the press tech comes in that way we
can get back up and running very soon tomorrow I'm going to come in and take the press off of
the pallet and set it down so I'll see you guys tomorrow it is another day I did not get the
press off of the base however we had to catch up with orders we're still working on things I did
manage to install an air fitting down there as well as I had to put my larger hose back in and
I also installed a little bit of a tap over there for air tools and all that and add to
switch out a breaker in the breaker box for the flash because it does require 56 amps so I put
a feeler 60 or 70 the press tech is on his way and Susie gets here we're gonna start uncrating
all these heads and putting it together this is manning the press deck from Anatole and he says
because he is on the video that if I get if we get famous and viral I get 90% of the royalties
on itself there we go Oh Mandy shows up and gets 90% after all the hard work I put into it yeah
90% borrowed the forklift if we're gonna move some things and get the base off of its pallet
right now hey I like pilot if you let me borrow it I get royalties
so Toltecs possibly PSC yes he hasn't done on the details will let you make more she apparently has
shown like a million people the video me falling out Richard oh really so that's how you get it
as you fall out of your care it's dead we are looking at the main board on top of here this
is where your main power comes in you got your PCB 35 which is your communication board that
talks to the main control panel you have your solenoid valves they will control your choppers
and you also got a little distribution board up here which is the main power for your AC
inverters so that basically is what sends power out there okay and that's pretty much
what it looks like in here until we get the main control panel with the touchscreen on there and
this is your inputs and outputs for your front and rear sensor or your printheads if you ever
have a question in regards whether your sensor is working sometimes even though the sensor might be
lighting up it might not be sending the input or output and you could actually test them by
actually bringing the head carriage forward to light up say the front sensor you'll see an LED
light up here you can push the carriage back to light up the rear sensor and you'll see the other
LED light up and that will tell you that the input is going to the board and then for those
sensors are things such as yes right here there's a sensor right here that sensor that's your horn
and this also says they're done here's one here to you that's for your lip up maybe your table up
and table down so there's only one cylinder that lifts the whole table yeah oh that last machine
had three this is your free wheel or your lock carousel helps and this is your lift for your lip
cylinder so that is for this guy over here which rotates yeah this actually rotates up and up this
is your actual index drive or your thermal run so and this is your lift cylinder obviously that's
where your main air comes in right so we'll bring our hose down hook down to here and that actually
goes into this regulator here right okay oh no what's what's under that this is all your out
drive you got a thermal amplifier in there can i play fortnight on it you can actually make
it a little to be that's your index PCB board that's what controls that drive sure and this
is your amplifier so basically your main control panel talks to is board this board talks to your
solo amplifier okay or your amplifier drive and that's what basically sends the pulses for the
mortar to magnets this guy talks about no is it like a kind of a screw yeah it's a screw
yes actually a screw mechanism just imagine a big screw going in and just kind of goes back
and forth back one yeah that's how the bolts work yeah kind of yeah yeah that's exactly basically
the other servo drives are pretty much the same way whether it's a bold but Titan or whatever
the machine is gots it and then you got your power supplies one power supplies actually its power for
you boards and stuff like that the other power supply slow for your safeties and stuff and for
your safety bars and yeah so you go if something like ten years down the road something comes up
is the machine smart enough to say hey it's this particular piece here or it's just it's troubling
matter of breaking it down and troubleshooting like let's say for example one of your safety
or your your bought your your control plan was now turning on well obviously you would test and
make sure that you're getting voltage to it come down here make sure you're getting 24 volts okay
let's make sense yeah so I was like man maybe it's not the point where it's kind of like a
card it just gives you a code yeah if it does you still have to break it down to where exactly where
that is right I mean like your alternator goes out in your car you gotta take your belts off
all right Manny just left we got all of the heads on this thing is a pretty big press Shannon didn't
mention that a little bit bigger I thought I was like yeah I said that same size it's a little bit
bigger got about as much space as we had to begin with you yeah very excited let me I'm gonna walk
you guys around and just kind of show you how it's looking so far so here we go we got nine
colors this station does lift up so that way you have an unload station here and you got a
load station which I have or ruv all nine colors then you would be loading and unloading from here
he's gonna come in tomorrow here are the arms he's going to put those on essentially I'll be able to
do some more film at it really didn't need a lot of help with these nice things or pretty heavy
pretty heavy much heavier than the the javelin that's for sure there's the flash right there
the monitor is back over this way and the safety bars are over back that way pallets over there so
we still got a lot of straightening up the dude but there she is we gotta move the tire back this
way but what kind of shuffle things around get some of this stuff out of the way that doesn't
to be there once this all set up and ready to go and there's a nice big bin of wood for the trading
not sure what to do about that well that's about it for today I'll capture some more
video tomorrow if you're new to the channel be sure to subscribe that way you don't miss out
on our vlogs of the day at all tighten em coming together and we'll see you guys in the next video