okay if you will please give him your undivided attention what we're going to
work through right now is how to build the nail puzzle project in fusion 360 so
we're also recording this you can't crinkle in the background
that's the absolutely silent but so you'll be able to go back and refer to
it okay you okay so we're gonna start off with just a sketch I normally like
to do a sketch on this plane right here basically we're gonna start off with a
center point rectangle we're gonna pull that out so - so there's our rectangle
now the easiest way I think to do this would be to make this come over and put
it at 75 or 0.75 inches and then we get one of these two-point rectangles and
grab that there and pull it down to there and then one
and then there's that so now I come from this angle I come over point seven five
and be the you're the exact same thing on this side and then after this is all
done we're gonna pull this out into a 3d part nice and slow nice and slow
so we're all in sketch mode right here were all done sketching it is contained
okay so that's our part right there so we're gonna say stop sketch now if I
click there's that part right there so now I'm going to grab the extrude tool
which is located right here grab that face and pull it out to 0.75 and let me
turn off the upgrade so there's the part right there now the next thing we're
gonna do is we're going to create a sketch on that at that piece right there
so that we can make our hole through the middle and we're going to take a line
and find the center point so you can move it along until it snaps to the
centre point and drag that down 0.5 and then come
over here at the sketch and get a center diameter circle place it on that point
right there and then it is point four centimeters and that's our hole so now
if I click stop sketch our holes right there and then I can click extrude and
pull that through and now we should have a hole going through both sides now
we're going to get into the nail which is a little bit more difficult because
it uses a lot of different tools so basically you want to use this plane
right here which is called an offset plane and you're going to pull it
through until it gets about to the center or close to the center so I can
interrupt you could go back one step how did you create that offset plan in the
first case okay so right here right above the construct down tab is offset
plane you basically choose a piece and then it turns up make it's a plane there
and then you can pull that plane out to wherever you need to get out of plane
somewhere else so then we're gonna okay and we're gonna create a new sketch on
that plane so basically that just divided and made a piece directly in the
middle so now I can grab a center point circle and if I put it here and I pull
it out this is the hole that is drilled through the wooden block so to make the
nail we're just gonna make it just a little bit smaller than that hole and
stop it there now I can pull that out to there so now I'm going to extrude the
nail out as a different part so I'm going to turn off the body get the
extrude tool pick that circle and turn it back on and then I'm going to come
over here to one sided so instead of having it just go out this way I'm going
to have it go out both sides symmetrically so now if I pull on this
side it comes out on both so there's a nail and now to make the head of the
nail we're going to make a new sketch on that piece
there take a circle find that center point which is right there pull it out
just a little bit bigger and then you have that circle there so now I'm going
to extrude out that little circle there off the end of the nail to get the head
of the nail and then you can put on some Philips to make it look more like the
end of a nail just to give it a little bit of a curve and now we're going to
get on to the point which is the final piece of this so we're going to use the
offset plane again and we're going to offset it off the end of the shaft of
the nail bring it out just a little bit and click OK now a new sketch on the
plane we're going to make a circle and since we want this to be extremely
pointy this might not be the best way to come it this is the way that I would do
it is 0.01 and that makes a tiny very tiny little circle right there that's
almost like a point so that right there is our point and we're going to use a
tool called loft which basically takes two shapes and makes a new shape that
will combine the two like that picture shows right there so we're going to loft
from the circle to the point which is going to make that cone and we have and
then we're going to color it now so appearance so basically I just
right-click off the part and click appearance which is the one with the
little colors and we're gonna come down here to wood finished oak and put it
right on to that you drag and drop yeah so it's a drag and drop so I click it
and I bring it out here and drop down to there and then you can also choose to do
bodies and components or just the face of the part like let's say you were
painting that piece red I could come and find a red paint turn on faces
and just make one side read so it kind of depends what you're doing but that's
basically a brief overview of some of the tools you can use in Fusion you go
through first how you save this file sure so that can't be how you create a
working dry okay so you're gonna come up here to save which is just a little Save
icon and then you're gonna name it so
okay and then you just click Save and then I'm correct you just click from
model to drawing from design and you click OK and then you can drop that in
there and you come to this and you click that and you pull it up up and then you
can do a top view and then you can also drag it out here and put the one in the
corner like that oh shoot I think right click okay
alright sitting there step and then then if you want a dimensioning tool up above
so you can put dimensions on there and then the other tool is the text tool so
you can fill in your title block so you put your scale in let's be size paper so
you get type inches on that or title block and then you drag it down into the
title block I was absolutely beautiful this is again
you're working drawing this working drawing is one that goes into your
portfolio oh and then up if you wanted to change the paper correct it's
huh double-click on that on the sheet I actually on the pulldown menu on the
sheet so access to its bodies clicking that up on the sheet type oh shit baby
on the basket strange