let's rang it out again I'm going to talk a little less will be here is grind
the top edge and the bottom edge off nigga up make sure it don't fly so it's
got a couple of cabins and narrow it up grind them out and then this coating on
the side is a plastic coating I'm better I got to find that off so it doesn't
melt off plus i'm going to be painting this so I want that operator so that's
what I'm doing that
this has got some slag in here that I'm going to get a hammer and knock that
slag off so it's easier to whittle done
okay what I got to do now is trace around the base of it and cut me to
place out with my plasma cutter it took me about an hour to get all that plastic
off their boy that was a chore all right I'm fixing to a difficult in here a
minute well guess what can't seem to think any yet well me neither my plasma
torch kicked off my breakers I guess I gotta shut a few things off in here be
right back well it was my heater in my henhouse runs off I got plugged in in
here and it you know pulls a lot of juice so they're going to be cold for
the waffle i get these cuts
man I love this dude
alright there's two of them I'm going to take
this in a while though shot put them on the grinder smooth these edges out I'll
be right back
okay what I'm doing now is cutting a notch out here for the chimney this is
where you're going to load the wood at and then inside the chimney goes up this
away I got to cut the notch out
let it run out of battery got to get another battery okay that fits that's
about how far it's going to stick out right there all right now I've got a
Wilma chin me together I don't quite have it cut out i'll cut it out will
together show you what that looks like before i put it in here
that's really smoky in here I don't know how well you can see but I got my top
cut for the chimney I got my chimney on welding so now let's do some drive-in
make sure we go we're going to work here
good so far just set well yeah it's going to work you see how close I got
you're looking at here
all right that's looking good I'm going to I'm going to weld the top on and then
I'm going to weld around around the chimney there and then I'm going to cut
some legs weld some legs and this is the bottom here that's facing up so but you
know what I could have a cup of coffee good lord it's just a little past noon
and I'm going to pass out from lack of sleep here if I don't get coffee I got
up to three o'clock this morning see you
well my quit feeding wire so i may have overheated it I gotta let this thing
cool that's you're supposed to well for like two or three minutes and it let it
cool for eight and I haven't done that so it might have kicked a reset button
off in there I'm just going to let it cool down but here is what I got this of
course will get cut off and i think i'm going to weld some some flat stock
across the top to give it like a pot standoff this is a little too long
probably going to cut about inch and a half off of that
and I got the one inch tubing in the vise
what I'm going to do is I have another welder I'm not going to get it out
though I'm going to probably stop yeah I'm gonna do that it's in the afternoon
and I've been messing with this you know most of the day in and out of the house
doing other things uh I gotta cook supper so I'm going to let this cool off
and I'm going to come back out tomorrow and finish this and if I can't get this
world of work i have another welder that I can use it's not as easy to use as
that oh my plasma cutter what a dream what a beautiful cut I do very very
little grinding to clean it up I'm glad I got it and here's the legs I'm fixing
to make the legs 10 inch and a 70-degree angle all right I'm going to put this
video up and tomorrow morning I'm going to get back out here and finish up I
mean we're going to turn a handle on my lathe the handle is going to be read
above the the feed tube it's going to be right in here and i'll turn it on my
lathe and stain it okay see you tomorrow