[ALARM GRID SOUND INTRO]
Hi, DIYers.
I'm Jorge from Alarm Grid.
Today, I'm going to be showing you guys how
to learn in a PowerG 9939 key fob to the IQ 2 plus.
Now the first thing you want to go to make sure
is that you actually have an IQ 2 plus.
If you guys have a normal IQ 2, meaning,
you don't have a PowerG data board
card built into the system, this key fob, unfortunately,
will not work with your system.
So you do want to make sure you have the IQ 2 plus.
As you see here, we have easily labeled up at the very top.
PowerG card is added to this one.
So this was actually a previously--
a normal IQ 2.
We got our hands on a PowerG data board card
and just installed it.
Normally, if you just have an IQ 2 plus,
it already comes with the PowerG data board card built in.
So you guys have nothing to worry about.
So this is a DSC PowerG key fob.
It is fully encrypted, and it's supposed
to work out about 600 feet.
I normally say 600 feet.
That's what we've seen our customers make it work at.
But PowerG is supposedly going to work at 2 kilometers
line of sight.
We just take into account all the construction and everything
that the signal has to go through.
So to learn this in, one thing you will notice
is while you're learning it in, you
do have to press and hold the button
and wait till the light illuminates on the second time
and released to button.
If you release after the first time you see light illuminated,
it will not work.
And I'm going to show you guys an example of that right now.
I'm going to go ahead and unbox my key fob.
Woops, wrong side.
Other side.
Now you see right out of the box,
the key fob comes with the alarm away, alarm stay, disalarm,
and a panic.
Normally, that's used as a panic.
It can be used as police panic, medical panic.
Had them tested for medical panic,
but you guys can certainly try it out
with your central station.
And then you have the little key chain at the bottom.
If you guys are going to take it and put it on your keychain,
so you guys when you get out the car,
easily disalarm it or alarm it when you leave.
The batteries on the inside.
If you guys ever need to replace it,
there's a small little screw right here.
You unscrew, it take it out, find the battery replacement
at your hardware store, put it in.
Again, these batteries usually last a long time.
But if you constantly use the key fob,
you may get a good two, three years out of it.
If you don't use it that often, you may get three to five years
out of it.
So I'm going to show you guys how to learn this in now.
So you will need your dealer code or your installer code
for your IQ 2 plus system.
Today, I'm going to use the default installer code.
But just so you know, default installer code and dealer code.
Installer code is 1111.
The dealer code is 2222.
You or your company may have changed it though,
so you want to make sure using the correct one.
So first thing, I'm going to hit the little gray bar
at the very top.
It's going to open up my menu.
I'm going to go to Settings.
From Settings, I'm going to go to Advanced Settings.
You got to enter in your dealer--
I'm sorry, installer code or dealer code.
I'm going to entry in 1111.
And I'm going to go to Installation, Devices, Security
sensors.
And I'm going to hit Auto learn sensor just because this is
going to be the easiest route.
Once I hit auto learn, the panel goes into listening mode.
So any sensor that gets triggered
will show up on the panel.
So make sure that you guys aren't opening up any windows,
setting off any motions or anything crazy like that
when you're trying to learn any sensor in.
Because then the serial number will come up.
And we can verify that all at the very end.
So now I'm going to go ahead and press down my star button.
That's the button that we're going
to use to learn the key fob into the IQ 2 plus.
And I'm going to do it the wrong way the first time.
So I'm going to let it go as soon as I see the light come on
from the very first time.
So as soon as you see that, the thing that most people do
if they see the light, OK, the key fob
is emitting a transmission and the panel will pick up on it.
That's actually incorrect.
Holding it down and letting the light
flash one time will not work.
As you can see, nothing came up.
But you will have to hold it down
for a couple of more seconds.
So now I'm going to press and hold it down again.
I'm going to let's--
I'm going to keep pulling it down even after the first one.
I only let go when I see the second one.
So I'm still holding it down.
That was the first one.
Now the second one comes up.
And now I release it.
It's going to say illuminated.
Start blinking fast.
And now it'll send the signal over to the panel.
And once the signal picks it up, it
will give me the serial or the tax ID number that you'll see--
I'll show you guys on the back of the sensor in a second.
As you can see, it takes a little bit.
So you want to make sure that you're patient.
OK, sometimes it won't work right away.
I'm going to go ahead and try it one more time.
A little bit further away.
Press and hold down.
The light we'll blink one time.
I'm going wait until the second time to release.
I release it.
There you go.
This time, it worked a lot faster.
So if it doesn't work the first time,
try again the second time.
Again, I tested it before the video.
It worked automatically.
Something happened now, it just didn't work.
But I went ahead and did it now.
So right there it says, sensor 3053920.
If I look at the back of the sticker,
it will also say on the ID number, 3053920.
I'm just going to hit OK.
And I just want to show you guys real quick
a zoom in of the sticker on the back of this sensor.
So you guys have an idea of where to find the ID.
It'll be in bold black letters.
It'll be in the center of that sticker.
And it'll say ID.
And it'll say the actual serial number that
came up on the IQ 2 screen.
All right.
Now I'm going to go ahead and get back
to programming the sensor itself or the key fob itself.
So after the panel picks up on the serial number
and you hit OK to confirm that it matches your serial number
on the key fob, you're going to go in and be
taken to this screen where you can program the sensor itself.
So you can give the sensor a name.
You can just leave it as key fob,
or I can give it a custom description.
So I can type in Jorge fob.
Yep, that's Jorge, actually.
Jorge, Jorge, same thing.
Hit the green check mark.
As you can see, it already fills in a similar number
up at the top left.
The sensor type, you obviously want
to make sure you leave it as a key fob.
It knows it's a key fob.
It's not going to allow you to change it.
But what you can change is the sensor group mobile intrusion,
mobile auxiliary, or fixed auxiliary.
So the mobile intrusion is referring
to the panic button, the little start button on the key fob.
If I leave it as a mobile intrusion, whenever I press
and hold down on my panic, it will set off a police panic.
If I do mobile auxiliary, that means it'll set off a medical
or whatever you have it program to.
Normally, it's either police, fire, or medical.
So here, it would be medical.
Now the top two are mobile.
Meaning that the system knows that you're
taking this with you.
It's worn.
It's constantly moving back and forth
between the location and your workplace
or wherever you're going in your daily routine.
The fixed auxiliary is if you have this,
let's say, in a drawer, in the house somewhere.
So it's-- these top two are not supervised.
Because if not, you'll be getting supervision errors
all the time when you leave the house,
because the sensor is not checking in with the panel.
But if you do fix auxiliary, then the sensor stays at home.
The panel is going to make sure to check in with the sensor
or to make sure it's receiving signals from the sensor
while the key fobs is at home.
And if it doesn't receive a signal,
then it will let you know, hey, I don't know what's going on.
But the sensor, it's no longer on site.
And so that's something you may want
to use if you guys are planning on leaving this in a drawer
somewhere and using it as a panic only.
So I'm going to leave mine as a police panic
so I can test it with you guys on video here.
As you see, the source actually already leaves it as a PowerG.
It knows it's a PowerG key fob.
The chime, you can give it a chime.
I don't know really what you would use the chime for.
So I'm not going to use that chime.
And voice prompts, I want to make sure they're on.
Because I want to make sure the system
is letting me know when I'm alarm away, alarm stay,
or whenever I set off a panic or disalarm.
So after I do this, I'm just going to hit Add New.
That's going to add the sensor.
And it's going to bring me back to the screen again.
So if you have more sensors, you can continue learning them in.
I'm done for right now.
So I'm going to hit the Home icon at the very bottom.
And it's going to bring me out to the Home screen.
Now when you're using the key fob,
you have to press and hold the button in order for the panel
to follow the command.
So if I do an alarm away, I'm going to press and hold down
the top left.
All right, one second.
I'm going to go ahead and press and hold.
Once I see the red, I'll go ahead and release it
and the command will go through.
The system is now going into an alarm way.
I'm going to go ahead and disalarm.
I'll go ahead and press and hold.
Once I see the light, I'll release.
Oh, it actually says my name in Spanish.
Jorge fab disalarm.
So that was an alarm away--
alarm away and disalarm.
I can do an alarm stay.
Press and hold.
Once I see the light, I release.
And I'll go ahead and disalarm one more time.
Now I will tell you guys this.
Because I tried it before.
If you guys set off a panic, you cannot disalarm the panic with
the key fob.
You have to actually enter in the code at the panel.
Why you may ask?
Security reasons.
So let's say a burglar comes in.
The alarm goes off and he finds your key fob.
You don't want him to be able to disalarm
your system if an alarm goes off or anything.
Or if a panic-- if you set off a panic because somebody
broke in.
You don't want them get the key fob and disalarm it.
So it's just for security reasons.
You cannot disalarm a panic that will set off from the key fob.
You actually have to enter in the code.
I'll show you guys that right now.
I'm going to press and hold.
cover my ears.
And it is going to be loud.
I can try disalarming it, but it won't go through.
I have to enter in the master code.
I entered in my master code.
Aw.
1234.
Now obviously, yours may be different.
Mine is just defaulted, so I have the default codes.
But you're going to want to use whatever code you have.
So after you disalarm the system, all is well.
Make sure that if your panel is monitored,
and you're testing a key fob, and you set off a panic,
call your company, called your central station,
and place your account on test before you set off a panic.
If you set off a panic, you might see the police
at your house pretty soon.
And you don't want to get hit with a false alarm fine.
A false alarm fee.
So make sure that you guys place your account on test mode
before testing a panic.
All right.
So this is just a quick video showing you guys
how to add a PowerG 9939 key fob to an IQ 2 plus.
If you guys have any questions at all,
feel free to send us an email to support@alarmgrid.com.
If you found the video helpful, make
sure you hit the little Like button underneath.
Subscribe to the YouTube channel,
and hit that little bell icon as well so
that you enable notifications.
So that way, when we upload new content, you guys get notified.
I'm Jorge, and I'll see you guys next time.