hey ladies and gentlemen it's drew with geoarm back again to talk to you about the adc sem
unit for the dsc power series systems so what i'm going to do here is i'm going to show you how to
get this wired in and get it ready for the point of activation what we need to do first is we need
to make sure that the dsc system is completely powered down you need to unplug the connections
from the backup battery which you can see i've already done here and you also need to unplug the
power supply once you have that done uh verify your keypads that there is no power and uh at
that point you should be ready to get this thing wired in so the first thing that i'm going to go
ahead and show you here is how to get this thing open so i've already pretty much got it open but
there's two clips down on the bottom here you just press them down and then this thing separates just
like so so there's two clips here just press them down pulls right off all right so once you look
inside here you'll see that i've already pre-wired this now this is the wire that'll be coming with
the adc sem unit which has a little fuse attached to it uh this wire you're gonna wire into what's
called plus 12 v it's on this very far left hand side terminal um once you get that wired in there
you're also going to need to get a a strand of a 22 gauge 20 gauge or 18 gauge four conductor wire
you're only going to need to use three of the actual wires inside of the uh you know the actual
strand itself but we we already went ahead and cut the red one off that's this was red black yellow
green i cut the red one off here because we're using this red wire so you'll see here that i
wired the white wire to y because i don't have a yellow wire in the strand so white here to y and
then green to g and then this black wire over here to gnd now while i have this open here i also want
to show you guys the optional ethernet connection which can be slid right into this point here
with this little device here so this little clip would just slide right into there like so
so this is optional you can hook internet up to this device if you choose to
uh it's a pretty cool little option for sure to make it a dual path communicator
so back to getting this device wired in now so we will get the actual power the positive power
applied last uh what we'll do is get these three connections made first all right so
the white wire in this strand is representing my my yellow wire because this doesn't actually
have a yellow wire so we're going to be wiring this into y e l now this is going to have other
wires in this terminal that's perfectly fine just get this wired in there along with it
and get it tightened up now the next thing we're going to wire in is going to be grn
which is my green wire and it runs to grn on the actual panel itself here let's get that secured
okay that's in place now we have the ground wire which will run to blk on the panel it'll
be labeled blk on the power series okay and once you have that wired in there this thing is set to
go as far as those connections are concerned now we need to get the actual positive power
applied to this so what would happen here is we would just be using the actual wire itself here
and running it to the battery like so so you would slide it onto the battery itself
and once you've done that there's a split connection that's on this that you're going to
connect the actual battery uh wire from the panel to so it just slides right on the top like so
and once you have that on you have both of your connections now made
on the battery and you have it wired in at this point you are ready to get this
activated so you're gonna need to give us a call make sure that you have your installer code handy
and you also have the alarm.com serial number imei number that we will need to get this going
do not power it on just wait to get it activated at because this is a a bus scanning device so it
will kind of make your panel act a little batty but uh this is the way to get the adc sem wired
into the dsc power series system if you guys have subscribed to our youtube page and click
the show more tab underneath the video where you can view valuable links pertaining to this product
similar how-to videos and our low-cost no contract alarm monitoring services