hahaha Pocket holchick was like that, OK, assalamualaikum warahmatullah barakatuh
, see you again with the reference BlackBerry r&o channel for yourself. Ok, in this video,
I want to show you the process of making a deiye Pocket holchick like this, it's
bigger than the one in the online shop. Yes, but because I made this myself, I'm more
satisfied with being asked, yes. So that was the function, yes, I agree, it's strange and roughly how
it is made, but don't forget to highlight and share because if it's not you, who else
is good, let's execute it okay, here we will starting for the manufacturing process, so for
the main component, namely this I use something like this, Eh, unseen hold real, so
I got this from a CBR or Megapro motorcycle piston, it can be the same size as the edril
I will use So the first one is for the band I'll split it first, if you have
prepared it with a thickness code of about 6 cm da n I gave a marking of 15° and I cut it
using an m show like this, so make sure the slope for the hole later is
15°. Friends, you can use a benshaw too, if you want to cut because I don't have
a benshaw, so I use a Gondang mic then I cut again for some parts,
which will be used in the process of making the Pocket holder now. Then for the rear slinder partition
, I will make it from wood, yes, I also cut it according to size
and after that I collect all the parts of the body which are made of wood.
From the straight slanted one, let's equate the size first, so for the size of the partition,
it's the same as the height of the cylinder. First, we make the middle position, we
just give half of the slanted part of Imam Sudrajat's potash and we measure the position first,
make sure the position first and we stick it with wood glue, yes, for this small partition, jan bro
, forgot to show the pressure and it's finished like this for the main part, then Hi, let's
tighten it with about sorry with a scrub, let's drill it first so that later the function will be so that
the partition does not move anywhere when we do the process of making
this holchick Then For the top, we connect it using a double, so with initial
at least two mating connections it will be stronger, and here we equate
the points from or the position of the first hole by moving well like this we equate and
we give the marks and marks. we board according to the diameter of the dawl that we will
use and we give glue so that it is strong So if we don't give the glue the wrath
will occur it will loosen or it might be prone to detaching so it's better to use
wood glue here or maybe if friends want to use Epoxy glue can also work, yes, we are
weird here, so make sure he is taught the same way as the top one the bottom
is for the body, yes. And after that don't forget to claim. Well, we put pressure so that it sticks
perfectly and after it dries. Now, here we put the world for the baby at the bottom
, because even though later I will learn too or play a little football again the thickness of
this tool, but still we have to make sure the carriage is perpendicular so that later when we do
the cleavage it becomes even more flat and more perpendicular too and don't forget
to grind it too, so the smoothing function is here, so that later when we do
the cleavage or cutting like that becomes flat so it's flash and flat too yes And And after
this for the top we use that slanted piece of wood like this so so
we leave two holes in the middle yes hi Strong Den with wood glue can also be with the name
Fox Yes, and after this, in the closing section, I will temporarily give
scrubs first so later it will be very influential in the process of strengthening the position of the cylinder hole
because I'm here using epoxy glue, so it's only temporary, then I
insert the cylinder folder like this and to strengthen the position of the holder I use epoxy
. I put it in between
, yes, it's the same as the problem until it completely fills the hole or the holes
on the edges of the real hold cylinder, yes. Then for the cream time, it's about 24 hours
. After that, it's dry, for the inside, we remove the screw. and we fill
the former scrub hole
with epoxy. We will sand
the remaining
dry Fox glue first, yes, all parts because there are some I covered the holes in the fields
with unevenness or wood defects, I covered them with epoxy glue too. For the likes, it's free,
friends, you can use the 2 40 Can Wear 200 or maybe if you want something faster, you
can use the 60/80 one, make sure the one for the whole part was taken away properly
and perfectly Okay, after this for the body, it's actually done, yes,
we can actually use it, but we need to test it here. Let's test it with wood first. Let's test
it. work using Hi, really adriel, usually
for those who use Holcim, yes, let's make a hole and after we see it's flat, it hasn't penetrated yet and it's still
thick , yes, yes.
it uses a table saw because earlier we
did the bottom alignment and it was perpendicular when we made that selection
It's also perpendicular and even, now it's like this, so the drill bit has gone through and formed an
angle and we'll see for the connection of the leaves to be visible and we need to cut this too
, because maybe it's still too long, we cut it normally using the military show
that was awesome sandpaper, so that it is even and smooth again, here I am using grip2
40 and we will try this in a ready-to-use condition and like this on the experimental wood,
yo yo, sir, it is claimed, yes.
I'll cover the seat directly for this body part. Let's just leave the
leaf part, it doesn't turn out to be the king, then I'll sand it later. For
finishing here, I'm using the Western outsider, Milan
. First of all, in essence, after the process
of making the main body, I want to make at the holder, yes, so the holder seems to be cutting it too, yes. According to
the design plan and friends, you are free to make designs
according to your own taste. it's
tilted, yes, it's like this and it
's a used cream tomorrow. But because of this, I use a broken clamp, it will automatically have to
adjust its position, we will treat it properly. For example, like this, so I
made a bribe for this claim. Yes, in this way, I drill first then I chisel it
, I
make sure it's sharp, don't forget to use it first, OK?
it's been this for a while I 'll give
korean glue first to stabilize its position and paper duct tape then eh s After that,
we drill to screw the frame so that it is in a strong position, we plug it in and out and
after the scrub is attached to cover the holes, to fill the void,
I use another line up here. Now while waiting for Foxy to dry on the body cream earlier
Yes, we made the next mount. My genie because the fox glue is still there. So I
'll just give epoxy glue for the wood connection. Yes, friends, if you want to use
ordinary wood glue, don't use epoxy and don't forget to put pressure on it too. And after
That's for the other side, we have started to screw it to strengthen it to strengthen the body holder
, we scrub at four points, yes and the same for the other side, which is something like this,
but before without any doubt, let's install the body first, the Pocket hold is
enough . again for the part of the holder that we will screw like this is the recording of the
contraction drill bit so it's for Kep School-style it's sinking so it's neater, okay? And after
that, we tried to install the body and this body can be disassembled, so we can
use it using this body and not using the body okay Then for the cream part, I
put it here, right here Yes, so let's adjust the size first so that later the claim is
also the maximum evil, we give a sign first to determine its position, then we make sure it's not
straight, between the holder and the cream, it must be Islamic, so that later
when we clean, we work when this tool when used, it becomes neater, yes, my way is like
this, yes, to determine the position of the body for the holder, then after we give the glue
, the book, Tighten it with screws from the bottom and for the cream part,
we are the same. Apart from giving us glue, we tighten it with Scrub, yes, I'm basically like this,
we give the valence and first, it's according to what I want it was gone, then we put it on and took it apart
, yes. And we wait for about three Epeng per hour, right here. Just me, it won't take long, okay, after that
it's dry, we claim, we remove it by installing screws to strengthen the position of the
valve holder. Well, it's like this Yes, the position is yes. And we test the cream, yes, and yes, yes, yes, yes, OK. Okay,
this is the original for the body, we put it on the Pocket hold, but before that, we finish like this. Here
, it's free, what do you want to use for finishing, but to make it easier, I use natural
oil. so the color of the wood becomes more alive like this, after we satisfied it, we
actually take a nap. We're actually sleeping. Well, after it's dry and we put it on, the body pocket hoodie
, let's test it on the workpiece, whether it works or not. Is the slope no
, let's test it using a special drill bit, yes, here, yes, finally it worked, yes. The point is that it
functions like that, so it follows the same Pocket hold it 's available on the market, yes, rather than me
, bro, it's better to make it yourself, and this will happen right away. And this is ready for
us to use, if for the process of making this tool, in terms of size, the waste is bigger
than the manufacturer, yes, maybe even from the material side, yeah because it's made of wood, so
it's not like the manufacturers who sell it in online shops or marketplaces, yes, and for
the advantages, it's cheap. Because I use used tires, yes, this is the part of the motorcycle or the
motorcycle, the piston is pure, the G glue is broken, right? whoever it is and the wood, it's wood
that doesn't use OK. Then for the drawbacks, the name is also wood, so there's
still a lot that needs to be upgraded again, it's not perfect, but the most important thing to
pay attention to is the degree of inclination of the hole position The drill is here, so don't forget
to set it to 15° so that the results are the same as the factory Pocket Holchick
. first, for videos from me, hopefully it will be useful and don't forget to
subscribe like and share and turn on the bell so you don't get the next video from us