Welcome to Sage Audio. Today we’re covering the Top 11 Stereo Width Tips. But first,
If you have a mix that you need mastered,
send it to us to receive a free mastered sample of it with the link in the description.
Don’t Use Delay-Based Stereo Expanders
Although you can get away with using delay-based stereo imagers on an individual instrument once
in a while, you should typically avoid them due to the phase cancellation that they cause.
Granted phase cancellation will always come into play when widening the image,
but certain expanders cause more artifacts.
This is especially true when it comes to your mix bus or master,
where you should almost never use a delay-based stereo imager.
Let’s take a listen to one being used on the mix bus, and notice how the mix becomes washed out.
Using Left-Right EQ
A safer way to expand your stereo image is to use a left-right EQ and create 2 bells,
one on the left and one on the right. Then vary their frequencies slightly - this will
cause the left and right channels to be louder but at different frequencies.
As a result, the image sounds wider,
but without too many artifacts or unwanted phase cancellations.
Let’s take a listen and notice how this sounds much cleaner than chapter 1’s demonstration.
If you’re enjoying the video, hit the like button; it helps us bring you more videos
Using Mid-Side EQ
Similar to our last chapter you can use a mid-side EQ to expand the stereo
image - you can pick which frequencies you’d like to expand and amplify them
on the side image or attenuate them on the mid image. A high shelf on the side image works well.
Or say I want to processing on the vocal to come through a bit more,
but I only have the stereo mix, I can increase roughly 2kHz on the side image with a bell.
Let’s take a listen to these 2 filters being added to our mix bus.
Natural Sounding Stereo Placement
When mixing, if you create 2 identical signals, you can use an EQ on one to cause
natural-sounding stereo placement. So say I want my guitar to be on the left - I can duplicate it,
pan the 2 tracks hard left and right, then EQ one.
For our example, I’ll use a high-pass filter on the right guitar, making the guitar’s lows
sound as they’re on the left. By duplicating and panning left and right,
we basically have a mono signal since everything is identical - but making
this change to the frequency response will shift the perceived placement.
Let’s take a listen and notice how we can shift the placement.
Only a small percentage of people that watch our videos are subscribed, so if
you’re enjoying the video consider subscribing. It’s free and you can always change your mind.
Using Mid-Side Saturation
If we have a mid-side saturator, we can saturate either the mid or side to add more signal to one
or the other - this creates a more centered or expanded image respectively. For example,
I’ll saturate the mid-frequency range, and pan the saturation to the side to make it wider.
Since the saturation isn’t always happening, this expansion will be program-dependent as well.
Let’s take a listen and notice how the subtle expansion is dynamic.
Modulated Mid-Side Saturation
If our saturator offers modulation, we take this a step further by linking an oscillator or envelope
to our panning or a drive function. For example, I’ll create an envelope follower, and attach it
to the drive functions panning - so that when we get a transient, the harmonics are panned.
Similar to before, we get dynamic saturation - but this way we have
more control over the behavior of the saturator.
Let’s listen to this example, and consider how it’s different than the previous example.
Dynamic Mid-Side or Left-Right EQ
If our left-right or mid-side EQ offers dynamic processing, we can use it to make our expansion
program dependent. So, let’s create some of the same bands that we used in chapters 2 and 3,
but this time, make them dynamic and increase their ranges to expand the bands.
We’ll notice that the expansion is now contingent upon the incoming
signal - in turn linking the dynamics of the track and the stereo expansion.
Let’s take a listen and notice how it varies from the demonstrations in chapters 2 and 3.
If you're enjoying the channel, join the community with the link in the description.
Mid-Side Compression or Limiting
If a compressor or limiter offers mid-side compression or limiting, we can use it to
dynamically expand the stereo image. The reason is, the most powerful signals, like the kick
and bass, will typically be in the mid image - causing more compression to the mid than the side.
As a result, whenever the kick or bass hits, the mid will be compressed,
leaving the side at a louder level comparatively. This isn’t the best
technique for retaining dynamics, but it works well at stereo expansion.
Let’s take a listen.
Mono or Stereo Low Frequencies?
A common question is whether or not the lows should be made mono, or kept stereo.
On one hand, you get a more driving low range and reduce phase cancellation,
on the other you may lose some of what makes the mix unique.
You can use a high-pass on the side image to cut the lows from the side,
and from there determine the cutoff. As you’d imagine,
this will reduce the width, but it can have a very beneficial effect on your mix.
Let’s take a listen to the lows being made mono up to about 100Hz.
Creating Wide Transients
One challenge with stereo expansion is making the side image more detailed since a lot of
softer elements are on the side. One solution is to duplicate the signal,
use the free plugin MSED on both, and isolate the mid on one channel and the side on the other.
Then place a transient expander on the side imaged signal. This is a bit unorthodox,
but it has a cool effect that’s difficult to achieve otherwise.
Let’s take a listen to it and notice how much detail we can get on the side.
Separating Mid and Side for Processing
Similar to our last tip, we can use this same MSED plugin to separate our signals,
and then use any form of processing discussed before to process our mid and side separately. So,
say we don’t have a mid-side EQ, now we could simply EQ the side channel.
The same could be said about compression, expansion, or any other form of processing.
Let’s listen to mid-side equalization, but use an analog emulated plugin on the side channel
that normally wouldn’t offer mid-side processing.
Let’s listen and notice how we expand the stereo image.
If you have a mix that you need mastered, send it to us to receive a free mastered sample of it
with the link in the description. Thank you so much for watching.