hi welcome to Robojax. in this video we are going to test and see how we can use the eye
shine TX 0 3 fpv camera and transmitter this is 3 + 1 which means we have a camera 600 tvl
wide-angle camera we have transmitter and also we haven't clover leaf or leaf antenna
this is 5 gram very lightweight and the power is after 200 milli watts so that's amazing but
it is selectable for short distances you can select 25 50 or 200 millivolts and operating
voltage is between 2.2V to 5 volts so you can either have a so you can either have one of
these tiny battery connected to directly or maybe just put your own 5 volt regulator to
use this F TV transmitter so let me show you how we can use it and how can we set this up so this
is a package very tiny that you just open it so the actual transmitters so this was a cup
so this is the transmitter and the transmitter camera and antenna so let's see what else we got
very well to text it so we have another power cable that you connected and we have a manual
very nice clean English manual so that's good and so here we are getting all this in a package
that arrived so that's it so this and the camera operates with 2.5 to 5 volts so I can just test
it here with one cell battery this is about 250 milli ampere an hour so and the camera has all
solar display which shows you some power channel and group of bands this is a 600 TV line lens the
power output can be adjusted with 25 milli watt 50 megawatt and 200 milli watts and here is a switch
so this is a camera very close-up and this is the switch that you push with your finger to change
the channel I'm trying to give you very close-up view of this camera so very nice display to give
you information this is extremely helpful and the antenna is also good it has been soldered very
well of course it will not withstand any crash but it is well enough so this is a connector
so that is connected now let me just connect that power so once you connect the power so
now it shows the screen will always flicker unless for the first time when you connect
it will be zero but other than that so it's flickering now it shows we are in channel for
B group B and this line at the middle this one line it shows the lowest power which is 50 watt
so this switch can be pressed and short or longer method so let me just press it if I just press it
one short and just change other channel 5 SEC's as you can see it goes to seven when I press it
again one to eight of those channel and one band so if for if I want to change the band just press
it for more than two second so now we are in B I'm pressing it again it goes to e F are you Oh
L H and then it comes back to a so now we are in a and leave it for a few seconds it goes to
back so we are in a 8 and the power is lowest one line so we have one two or three lines so
now let's change the power to change the power hold this for five seconds which means longer
than two seconds because if you press it for two seconds it goes to the band selection so short
press will change the channel okay so for two seconds we'll go to the band if I hold it for
more than two second so now it's in the band if I leave it returns back after this flickering any
short click will change it so now to change the power let's hold this for five seconds
okay so now this is one if I press it again it means two so now it's hundred milli volt and
this is 200 milli watts so press it again zero that is off so no transmission and that is now
it's at 50 so if you leave it for a few seconds so we are in a three at low power so now let's
test it so this is my fpv receiver I'm just turning it on so now we are as you can see
here we are in a low power 3 so we are in a 3 now as you can see here it shows B I don't know
if you can see it so I can change with a group now b c d a so now I’m an a to change my channel
seven eight one two three so this is a three now I'm getting
the signal and here is my screen and so this is a video from this camera
okay so this is very wide angle so let me just move it to close to my screen and you
can see that if the video from the backyard so the power was 50 so now let me press this and
hold this for tooth for five seconds now the two line now that is a 50 millivolt so leave it that
goes back so that three line is 200 milli watt so we have 50 we have 25 50 and 200 milli watts to
understand the meaning of channels the channels and frequencies have been divided into groups
here or band so we have from a to H here they mention it but you will not be able to receive
it on your receiver so some of these channels have been merged or frequencies are very close
so you will have to play and see which frequency will work but in each band for example a we have
from one to eight so we have eight and then nine here so that's why you have so many two channels
8 times 9 but depending on your receivers you can select one of these and then the this transmitter
will transmit that selected frequency for you so you can get a clear channel so that was a
introduction of how to use the in Shine TX 0 3 fpv transmitter web camera thank you for
watching please thumb up the video if you liked it and also please subscribe I appreciate it
you