in this video I'm gonna show you how to assemble the iSpring RO water system the six stage system
it's the RCC seven model I have the links in the description below first if you want to watch my
unboxing video go ahead and do it it's gonna be in the left corner the very first thing you
want to do is lay everything out like I have it that way you know that you have everything
and you're ready to go you don't have to do these in order but first find one of these
valves and your pressure tank take some teflon tape that they provided and wrap it around this
thread in such a manner that in the same direction clockwise that you're gonna be threading this on
like this and then screw this on
chert to tighten it where it feels fairly snug next make sure you unwrap all the
filter elements but pay attention to this one in the flow direction that
it's pointing because you want to keep it up like this so that's how you would
install it into the filter Center them all so that that little piece is in the center
like that now careful these are rubber seals that could come off so if they come off but make sure
they're on I don't think they should come off unless you're messing with them next take the top
place it on like this and then slowly try to align the filters in the center you can screw one at a
time this is what you don't want to do I wasn't paying attention and I put my first stage on third
this one's good this one's on the first so I'm gonna swap them so this is what it should look
like because if you would have swapped the filters your carbon filter would have seen all the dirt
first therefore when it would clog up much quicker versus you have the sentiment filter scratching
all the debris and dirt and rust and stuff like that first and then your GAC and then your block
carbon so make sure they're in proper order if you don't think you have a good tight fit with
your hands you could use this wrench don't over tighten it though because it is going to be harder
to untighten it when you're replacing the filters next we're gonna install this membrane make sure
when your openness that you're cutting it away from the membrane because you don't want to damage
it when you're opening this package don't take it out right away until you're ready to install it
just so you don't contaminate it so the membranes gonna go in here and we have to unscrew this but
before you do that you want to remove this tubing so to do that there's this blue clip remove it
with your fingers then you push this down and then you pull it out once it's pulled out then you can
unscrew it if it's tight and use this wrench you can lift up the membrane from these clamps so that
way you can get this on it on under it then move it make sure that the cell ring stays in here they
gave you they do have some spare o-rings which is good in case you lose this one or gets damaged for
whatever reason you have a leak then you take your membrane hold it by this plastic piece take it
out try to hold it by the plastic piece and make sure you don't you put in the two o-rings on the
inside this way then just push it all the way in but make sure that it's the o-rings in there and
slowly close it now I'm gonna use the wrench to tighten it as well yeah clamp that back in there
should you press this you put the fitting back in there as far as it can go I don't remove that
if you can't do it with your nail maybe use a screwdriver or a knife and put this blue clip
back in there so this is a alarm there's a probe basically when water touches the probe it makes a
connection an alarm goes off supposed to point it down like this in a wet area in case there's water
leak or something it's gonna signal so you want to put it under your sink somewhere where you can
see so the main thing you need to do is you open the back right here you get two screws put in the
standard 9-volt battery back in there like this close this and then take a screwdriver and screw
these in the system came with this paper which has a very good visual of how or all the tubing is
going to be laid out so next we're gonna install this under the sink take the faucet and remove
them in it take the faucet and the washer and put it on the thread make sure that the rubber piece
of the washer is pointing down before installing make sure you drill a nice hole doesn't have to
be big to fit in the faucet in my case there was a soap dispenser so I didn't have to drill
anything after you put it in there's gonna be this nut with the washer that you're gonna have
to tighten it to hold the faucet in place here's what it looks like make sure the faucet is nice
and sturdy it's not retighten in front next we'll attach the blue tubing to the faucet as shown in
this diagram but first you have to put the nut on the tubing and then these plastic ring and
this fitting that goes inside the tubing then you insert that into the deposit and tightening the
nut it could drill that matches to the size of the tubing and drill a hole horizontally into the sink
drain pipe after you drilled the hole make sure the tubing fits nice and dug take it out right
you're installing the saddle you're gonna want to put this gasket type of material around the hole
first put the saddle and with the tubing make sure the tubing is all the way in and hitting
the wall that way we'll won't make a lot of noise then install the second half tighten the nuts now
when you put the nuts you get a make sure there's a hex in there and they that it fits right into
it tightening the screws to where it's snug make sure it'll over tighten it it is a plastic piece
and you don't want to crack it lastly screw in the fitting to hold the tubing in place install
this white valve on your cold water feed to your sink basically it will be between your shutoff
valve and the hose that goes to your cold sink make sure you use plenty of teflon tape on the
connections this will be your feed for the water system remove the blue clip and insert
the red tubing reinsert the blue clip next we're going to install the yellow tubing into the top
of the pressure tank by removing the blue clip putting the tubing in and reinstalling the clip
again position your RO system and desired under the sink location and remove all the blue clips
from the connection points that will be installed and lastly hook up all the colors that are shown
where yellow is from the tank blew into the sink red is the feed and black is the train and lastly
open all the valves let the system fill for five to ten minutes and then test your faucet thanks
for watching if you have any questions leave a comment below and don't forget to subscribe